Search:

Type: Posts; User: blackcat4866

Page 1 of 20 1 2 3 4

Search: Search took 0.11 seconds.

  1. Replies
    4
    Views
    251

    Re: P2040dw add paper to cassette

    Sounds like something I could fix with a flat file. =^..^=
  2. Re: Bad print only on black Konica Minolta C220

    What interval between voids?

    It looks like black developing to me.

    =^..^=
  3. Replies
    4
    Views
    164

    Re: Xerox Altalink B8065 DADF multifeeds

    Pad separation increases page separation with a stronger spring.
    Roller separation increases page separation with a WEAKER spring.

    Which do you have? =^..^=
  4. Replies
    4
    Views
    164

    Re: Xerox Altalink B8065 DADF multifeeds

    Is there a DF separation adjustment? If not, I have had success installing weaker (yes, WEAKER) separation springs to increase page separation. =^..^=
  5. Replies
    7
    Views
    384

    Re: p3145 fuser problems out of box

    I'm surprised, frankly.

    You complain about a heavy media not fusing, but will not attempt media type changes, or even figure out what media weight it is? A person with over 30 years experience...
  6. Replies
    4
    Views
    159

    Re: Hello world

    Welcome! =^..^=
  7. Re: BizHub7228 - Possible to turn on DCPS' Sub Power 24VDC via emulated control signa

    I created a "copier in a box" from a Sharp Tiger AR-M280.

    This particular model had spare DIMM sockets on the controller allowing the copying of the firmware DIMMs. So I scrapped the engine and...
  8. Re: BizHub7228 - Possible to turn on DCPS' Sub Power 24VDC via emulated control signa

    Yes, that's my question too.

    What symptoms? What are you trying to fix? You skipped over that part.
    =^..^=
  9. Replies
    7
    Views
    384

    Re: p3145 fuser problems out of box

    Start with my questions, please.
    =^..^=
  10. Re: Kyocera P7240 belt cleaning station noise

    I had this happen after installing Maint Kit A in a Gemini. The primary transfer cleaner was significantly more difficult to turn on the new part. After watching the belt jump (and scratching my head...
  11. Replies
    10
    Views
    617

    Re: TA 4012i Fuser Unit

    That doesn't look like enough characters for a Kyocera part number. Try throwing in an extra "V" ... 302V693040 Fuser FK7127

    =^..^=
  12. Re: Kyocera 8353ci very strange laser related problem

    I've seen Toshiba lasers present this way when defective. Calibrate 15 or 20 times and it looks good ... until the first time it self-calibrates.
    =^..^=
  13. Thread: C2950

    by blackcat4866
    Replies
    2
    Views
    190

    Re: C2950

    The manual points to a communication issue between the motor control PWB and the engine PWB.

    If you're not ready to go for the engine board yet, you could try the harness in-between. The manual...
  14. Replies
    18
    Views
    942

    Re: Kyocera 2552ci only prints on reboot

    This is what I was thinking about.
    You wouldn't use a WSD port, right?
    Maybe a duplicate IP?

    =^..^=

    =^..^=
  15. Replies
    7
    Views
    384

    Re: p3145 fuser problems out of box

    Have you tried changing to a heavier media type setting? What gsm is the "light card stock"? Does it have a gloss or texture? Have you used Plain paper? Does it fuse properly?

    Try the simple...
  16. Replies
    8
    Views
    326

    [Jamming] Re: Canon ir2870 jam problem

    Is it obvious? Can you be more specific? Paper size and orientation maybe? =^..^=
  17. Replies
    14
    Views
    782

    Re: Image "repeat"

    Try these:

    =^..^=
  18. Re: Bizhub C258 artefacts, strange lines on printouts

    How about internal prints, like the management list or configuration page? Do you get any of the original image?

    If you emergency stop the machine mid-print, is there a properly developed latent...
  19. Replies
    14
    Views
    782

    Re: Image "repeat"

    Both sound like great workarounds! Unfortunately the typical MFP enduser cannot understand that machines have limitations, and may not be able to make a perfect reproduction of every possible image....
  20. Re: PRESS 6120, warped drum claw assembly

    5M copies later: no re-occurrence. My MacGuyvered drum claw assembly is working just fine, with no additional heat deformation. Whatever occurred before has not repeated. =^..^=
  21. Replies
    2
    Views
    179

    [Misc] Re: TA 4500i dark background

    So you've wiped out every adjustment. What were you hoping to achieve by doing this?

    I think that I'd do the image adjustments, and color calibrations. for starters.
  22. Replies
    2
    Views
    178

    Re: Konica c3351/3851 Thoughts?

    Few differences. =^..^=
  23. Re: C-458, "Function Cannot Be Used Because the Scanner is Not Available"

    It would have been a good idea to print off the management list to at least see what the error was. =^..^=
  24. Replies
    12
    Views
    724

    Re: Print quality problem C284

    +1 on all of this.

    I always listen and consider what the enduser tells me.
    Then ... I make my own observations. Rarely, do I come to the same conclusions. =^..^=
  25. Replies
    14
    Views
    782

    Re: Image "repeat"

    I would make a wild ass guess that that is a drum interval: ~96mm". I would suspect poor charge cleaning on one of the drums. Maybe poor drum ground.

    It would be informative to make digital...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4