Search:

Type: Posts; User: ZOOTECH

Page 1 of 20 1 2 3 4

Search: Search took 0.68 seconds; generated 48 minute(s) ago.

  1. Replies
    24
    Views
    854

    Re: MX-3640 unable to access network settings

    Can you get to the web page through a crossover cable with the laptop in the copier's current IP range?
    If so, you can make changes there, reboot and then change settings.
  2. Replies
    4,453
    Views
    751,523

    [Funny] Re: Joke of the Day

    Sorry, this is a repeat from 2010 ( but is still funny);

    - TEXTING FOR SENIORS



    Since more and more Seniors are texting and tweeting there appears to be a need for a STC
    (Senior Texting...
  3. Replies
    56
    Views
    10,032

    Re: Aneurysm it's still the administrator?

    TMI
  4. Replies
    4,453
    Views
    751,523

    [Funny] Re: Joke of the Day

    I am embarrassed to admit my guilt to the above post.😩
  5. Re: Wanted: Sharp AR-M237 Paper Delivery Exit Assembly - OR - Delivery Roller Holder

    Your best bet is to upgrade to a current machine! They will be able to save/send files to cloud, etc
  6. Thread: MX-M364

    by ZOOTECH
    Replies
    10
    Views
    1,669

    [CQ] Re: MX-M364

    Have you checked if the operator put machine in "Toner Save"?
  7. Replies
    56
    Views
    10,032

    Re: Aneurysm it's still the administrator?

    Help me please, I gave "SP" a negative review, and he responded by PM "800000000D"; I"m not versed in code or binary, so that 'slam' went right over my head. Should I be insulted, or just let it be?
  8. Replies
    56
    Views
    10,032

    Re: Aneurysm it's still the administrator?

    Hold on a bit, I've run out of popcorn😉
  9. Replies
    2,334
    Views
    1,475,079

    Re: Just how Crazy is Donald Trump!

    The Democratic Letter to Ukraine - FactCheck.org

    From all the sites "googled" from other posts, I find The Hill to be most centered, thank you for that.
  10. Re: MX-M904 Finisher Jams in the Saddle Fold entrance area.

    Try the finisher without the punch unit; I would be surprised if the jams still occurred. The punch units had a problem of 'gumming' up, and causing jams.
  11. Replies
    1
    Views
    751

    [Misc] Re: MX-6570 with MX-LC19

    The rear latch has a microswith that will not be enabled if the LCC is not level.
  12. [Misc] Re: Sharp MX-B402 - How to access simulation mode

    I could be wrong (again), but I believe the sequence # * C *
  13. Replies
    6
    Views
    519

    Re: website default calendar

    It's been that way since 2010; most likely after a system upgrade.
  14. Replies
    24
    Views
    1,894

    Re: Sharp MX-M904 Still Good?

    I believe that is the one, but you should check with a current tech/dealer - I've been retired 3.5 years without access to latest bulletins.
  15. Thread: pay grade

    by ZOOTECH
    Replies
    5
    Views
    427

    Re: pay grade

    If you find out the average tech pay for that area, make a deal with the owner that you will accept that pay for 3-6 months, and if you have exceeded their expectations, you would want a review with...
  16. Replies
    24
    Views
    1,894

    Re: Sharp MX-M904 Still Good?

    You may need the LCT Mounting kit (RB16), if I remember correctly.
  17. Re: 34 reputation points were taken with red card by somebody, help! Moderator

    And, those that contribute both monetarily, and with their know how keep this forum open. Anerisum, I believe, could not keep this site going if there were not contributions.
  18. Replies
    8
    Views
    558

    Re: MX-354 keeps getting F2-40 errors

    With the toner cartridge removed and front door cheated, run SIM 25-1. If it's not in the range given above, you have an over/under toner level.
  19. Replies
    7
    Views
    689

    [Jamming] Re: MX-3570V Duplex misfeeds

    Does this machine have a right side exit tray? I saw the cable/connector for the reverse solenoid not properly routed causing the solenoid to not fully open.
  20. Thread: Smoking?

    by ZOOTECH
    Replies
    72
    Views
    9,045

    Re: Smoking?

    Good for you, I think you have conquered this addition.
  21. Re: How to train customers to not replace toner early?

    Yes, as I remember there is a SIM code that will release the toner lock (for maint. and transport).
    The customer would not know how to remove cartridge, unless given the SIM code.
  22. Replies
    4,453
    Views
    751,523

    [Funny] Re: Joke of the Day

    This is probably a repeat, but courtesy of "The American Legion Magazine": A thief tried to steal paintings from the Louvre in Paris. He was caught two block away when he ran out of gas. "I had no...
  23. Replies
    3
    Views
    490

    [Misc] Re: What is MX-5070N USB B port

    I believe it is for updating firmware.
  24. Replies
    10
    Views
    1,426

    Re: How Much For Rent??

    Going rate depends on CPM, and wheather supplies are included; base rate plus copies/prints made.
  25. Replies
    14
    Views
    1,248

    Re: Happy 4th to all ...

    The OP mentioned that "liberals" hate America; that is where the politics started. I only mentioned that regardless of left or right leaning, that the 4th is celebrated by Americans.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4