Search:

Type: Posts; User: arnh79

Page 1 of 15 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    13
    Views
    324

    Re: Using D-FC65 developer in e5506AC machine

    Thanks for this! I've confirmed the dev material is 410 g in both series. So there shouldn't be an issue. I've order a bottle of D-FC556-Y so I'll have it in case I need it. Worst case scenario is...
  2. Replies
    13
    Views
    324

    Re: Using D-FC65 developer in e5506AC machine

    The claim of "lifetime developer" has been such a frustration. I found the e5540c series particularly bad at losing dev. That's why I have some dev for that series still in stock. I'm shocked how...
  3. Replies
    13
    Views
    324

    Re: Using D-FC65 developer in e5506AC machine

    I don't think so, but I'm willing to be corrected. :) D-FC65-Y is the part name for developer in the e5540c series. On that series you remove a hopper assembly that resides between the toner...
  4. Replies
    13
    Views
    324

    Using D-FC65 developer in e5506AC machine

    Has anyone tried using developer from an e5540/5560c series machine in an e5506AC series? I have a 7506AC that will be replaced in 2 months and the Y dev is depleted despite only having 250k on it. ...
  5. Thread: 3015AC CA00

    by arnh79
    Replies
    10
    Views
    540

    Re: 3015AC CA00

    It might be worth checking the shutter assembly for the IQC sensors. There is a weakness on the first version of that assembly. The pin that the shutter swivels on breaks. Do an output test to see...
  6. Re: Samsung SL-X4300LX - doesn`t print, no errors, led still blue

    It sounds to me like User Access Control is enabled. If a job arrives but doesn't have the proper authentication it will delete it instead of printing. Check the job logs after the blue light...
  7. Replies
    5
    Views
    273

    [Misc] Re: Dispose of used toner

    I believe there is a secondary detection for waste toner full on those machines. If the waste toner auger is pushed towards the rear of the machine it activates a sensor that will also cause "waste...
  8. Replies
    7
    Views
    361

    Re: Load LT-R and press [START]

    I see you listed 08-9164. On setup of every machine we set that to 1 so that if paper is on the bypass it will just start printing without needing a prompt from the panel. I wasn't sure if desired...
  9. Re: What problems do Lexmark MS331, MB3442,M1246, XM1246 have, any advice?

    I agree, manufacturing quality control has been an issue. But once they're in the field I haven't had any major issues. The image unit doesn't always go full life, but easily replaced under...
  10. Replies
    4
    Views
    332

    Re: Deleting image when printing jpegs

    I had this exact issue yesterday. Switch from Windows Picture Viewer app to Windows Photo app and it works great. I hate that Windows leaves legacy apps, like Picture Viewer, when updating. Just...
  11. Re: Samsung SL-X4300LX - replace old imagining unit with used one

    Same here. They are swappable, but the count stays with the unit. So if you put a 0% drum in a different machine it will show as 0% in the new machine as well.
  12. Replies
    6
    Views
    439

    Re: toshiba 4540c pulling developer

    I just want to say a big thank you to everyone who contributed to this post! I had the same issue, and it turned out to be the LED array. Since there was no copy quality issues before the dev was...
  13. Replies
    6
    Views
    439

    Re: toshiba 4540c pulling developer

    I've had similar issues on the e2830c series. After a lot of parts replacement, it turned out to be the main charge block on the copier frame. I have an e3540c that's starting to do the same thing...
  14. Thread: e-Studio 2505ac

    by arnh79
    Replies
    1
    Views
    250

    [Error Code] Re: e-Studio 2505ac

    08 - 6190: set to 0 (master PM counter)
    08 - 9891: set to 0 (individual parts PM message off)
  15. Replies
    6
    Views
    279

    Re: Toshiba 5055c Ghosting

    It certainly looks like a drum and blade issue to me. What does the PM count say for the black drum unit? Just from the pic, I'd say you could get away with replacing the drum and blade. We...
  16. Replies
    5
    Views
    428

    Re: fuser wrap jam clear

    I had to replace a fuser drive assembly on that series for intermittent errors. I never saw the one you've described, but it could be the cause. Also, the fuser units on the Samsungs are garbage....
  17. Replies
    5
    Views
    428

    Re: fuser wrap jam clear

    What model are you talking about?
  18. Replies
    13
    Views
    12,601

    Re: Toshiba E-studio 2500c scan to file?

    One additional thought: If you're on Windows 10 it won't work by default. The e2500c series doesn't support SMB v.3 and Win10 won't connect to a fileshare that doesn't support it. You'd have to...
  19. Replies
    5
    Views
    524

    Re: xm1246 fax issue

    Do you mean they had the cover page option enabled on the Lexmark, or they were physically sending a blank sheet as the first page?
  20. Replies
    5
    Views
    524

    Re: xm1246 fax issue

    I've been struggling with the same issue! I was told there is no option to print image on a confirmation report, but it's interesting that you say you have the same model and it does print an image. ...
  21. Thread: 3560 background

    by arnh79
    Replies
    4
    Views
    375

    Re: 3560 background

    This is a trip down memory lane! Most common cause of background on that series is optics. Clean the mirrors and then adjust the 05 exposure settings. (I can't remember those codes any more) It...
  22. Replies
    0
    Views
    521

    PrintFleet alerts for low toner

    Has anyone had success setting up PrintFleet to send out alerts when Toshiba copiers toner waste reaches near-full threshold? The newer Tosh models all have the ability to detect when the waste is...
  23. Replies
    3
    Views
    646

    Re: Scanning to PC - Toshiba E-Studio

    If you're connected via USB then your only option will be to scan to a USB flash drive. You'll see the port on the right side edge of the copier. After inserting the stick press Scan button on the...
  24. [Misc] Re: Problem with e_studio 757 (dot on printed paper)

    Like blackcat said, replace the developer material. Your symptoms indicate that the developer material is worn out.
  25. Replies
    3
    Views
    668

    Re: XC9200 Series impressions

    So... nobody's worked on these?:D
Results 1 to 25 of 366
Page 1 of 15 1 2 3 4