Search:

Type: Posts; User: Hishamawada

Page 1 of 2 1 2

Search: Search took 0.01 seconds; generated 57 minute(s) ago.

  1. Replies
    3
    Views
    93

    [Jamming] Re: IPressC700 Jam Code 0118.

    something seems not right, most of this duplex issue occurs on high gsm media or low gsm media .

    I want you to remove the registration unit and check if there is any torn piece of paper there...
  2. Replies
    3
    Views
    93

    [Jamming] Re: IPressC700 Jam Code 0118.

    hello ,

    what is the media gsm used? is the media changed recently ?

    i would suggest you to change all the gears related to the timing belts.

    Hisham Awada

    Sent from my SM-G610F using...
  3. [Jamming] Re: Canon Imagepress C7010VP jam with felt-market paper

    hello ,

    this printer is way old and its service is kind of not easy . i have been working on them for quite a time .

    first of all i want to make sure you are using the correct paper profile...
  4. Replies
    3
    Views
    176

    [Jamming] Re: Canon ir adv 8205 60gsm paper problem

    hi , the sheets better be fed along their grain .
    it is a major factor in the digital printers as a whole when printing on low gsm media.

    Sent from my SM-G610F using Tapatalk
  5. Replies
    5
    Views
    224

    Re: ImagePress C700 Fiery not working

    Hello ,

    Check the rams for the fiery .

    Hisham Awada

    Sent from my SM-G610F using Tapatalk
  6. Replies
    7
    Views
    354

    Re: Canon IRC5045 grainy print quality

    Hello,

    There is several causes for this issue.

    If issue is common on all colors:
    1) It could be media issue
    2) Secondary transfer roller , inner and outer
    3) Itb belt
    4) Developer...
  7. Replies
    1
    Views
    155

    [Misc] Re: ir6275 finisher jam1124 help me

    Hello my friend ,

    Your issue could be from two things , either the paper is being wrongly fed or hit when it is exiting the finisher . Or the Paper is being curled a lot causing it to roll at the...
  8. Re: Prints are peeling on the edges on Bizhub C364 & C454

    300 gsm media is normal glossy paper and the stickers are for digital printers . yes compatible toner is used in both machines . Should i just increase the fixing temp for this specified thickness...
  9. Prints are peeling on the edges on Bizhub C364 & C454

    Hello,

    When printing on stickers (thick 2) and 300 gsm (thick 4).

    Tried slowing the speed of the fixer and still same , tried increasing the temp also same .

    Any ideas what i could do?
  10. Re: Canon ImagePress C650 auto correct color mismatch fails, mismatching colors issue

    Dont clean anything , just replace the drum.

    Go service mode - > situation -> parts replacement -> replace drum

    Only replace the cyan drum , for 500k the developing should be good, no need to...
  11. Re: Canon ImagePress C650 auto correct color mismatch fails, mismatching colors issue

    Ok good .
    Its a drum issue , the patches are not printed properly on the belt to be read by the sensor. Replace the cyan drum .

    Dont forget to go through the replacement procedure in the service...
  12. Re: Canon IR Advance 6555i Light copies and prints

    Copier tech have stated the solution , but i would like to add something.

    It is better to clean the black drum assembly , Since toner can be soiled and damage the waste screw. Check the blade...
  13. Re: Canon ImagePress C650 auto correct color mismatch fails, mismatching colors issue

    You can just restart the machine until the colors are well registered and dont perform the auto color mismatch . This will allow you to printing normally .

    A little bit of alchol 95 will not...
  14. Re: Canon ImagePress C650 auto correct color mismatch fails, mismatching colors issue

    Ok my friend ,

    For numbers
    1) the test should be on a paper with width 33cm to check the edges

    2)ok very good

    3) the patch sensor better cleaned with cotton swabs and alcohol , sometimes...
  15. Re: Canon ImagePress C650 auto correct color mismatch fails, mismatching colors issue

    My friend this issue have several causes.

    1)First check if one of your drums have quality issues (specially on 33 width). Along with developing assemblies. Test halftone PG for each color.
    ...
  16. [Dead] Re: Canon IR 7570 doesn't boot fully, flashing energy saver light, no screen

    Hello ,
    I have faced this issue on ir 8205.
    Mainly it could be a firmware issue or the main controller pcb 1 is defected.

    First try removing and connecting back the main controller .

    Next...
  17. Replies
    3
    Views
    257

    Re: Best office Printers

    Which models for kyocera and ricoh ? And do you have any idea about ricoh b/w printers ?

    Sent from my SM-G610F using Tapatalk
  18. Replies
    3
    Views
    257

    Best office Printers

    Hello everyone ,

    I am currently looking for the best brands for office printers for both color and B/W and i need to take in account the followings:

    1)Second hand printer with a very good...
  19. Replies
    13
    Views
    442

    Re: KM C280 print quality problem

    According to ur photos , since the cyan drum is on magenta now , then its a drum issue (the drum itself).

    The yellow lines if not visible on the yellow prints as white lines then its a blade...
  20. Replies
    13
    Views
    442

    Re: KM C280 print quality problem

    As mentioned before , it's a drum issue .
    For yellow it seems only a drum blade issue
    Cyan seems a drum issue. If you want u can try adjusting the background level or adjust the primary transfer...
  21. Replies
    0
    Views
    791

    Canon Parts

    Hello everyone ,

    I am starting my own business and I want a supplier for Canon printers , Imagepress c600 , c6010 also Imagerunner black/white printers . In addition to Oce DP line printers.
    ...
  22. Thread: oce parts

    by Hishamawada
    Replies
    1
    Views
    1,613

    Re: oce parts

    Hello my friend , i am also looking for a parts supplier for Dp line , if you have found a good source i would be thankful :)

    Sent from my SM-G610F using Tapatalk
  23. Replies
    2
    Views
    269

    Re: Canon IR 6565ii

    Hello,
    Since the specification state it takes 11x17 then it is , the parts inside this series cant print larger then A3 in width .

    But for the length you can try and activate the long sheet...
  24. Replies
    3
    Views
    387

    [Error Code] Re: Oce 3155 error M22103

    i would like to add that the machine was working fine before it was moved from one site to the other and this error appeared .



    Sent from my SM-G610F using Tapatalk
  25. Replies
    2
    Views
    200

    Re: hp Laserjet m5035

    when the machine is the ready the copy/scan section is faded and cant be selected. so something looks damaged from the boards but i have no experience working on this machine. so not sure if there...
Results 1 to 25 of 36
Page 1 of 2 1 2