Search:

Type: Posts; User: Scottb

Page 1 of 11 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    5
    Views
    240

    [Misc] Re: TA2551ci Main unit open

    has the conveying unit been replaced or had work done to it recently...if so I would look to see if the black cover that hides the board has been removed or if the sensor actuator is broke off of it
  2. Re: FS-1300D: How to remove black line on left edge of paper?

    are the side guides against the paper firmly
  3. Thread: PC-920

    by Scottb
    Replies
    8
    Views
    156

    Re: PC-920

    Sho you right... in that case since its most likely a aftermarket rebuild I would check the drum...you know to rule out drum blade failure....
  4. Thread: PC-920

    by Scottb
    Replies
    8
    Views
    156

    Re: PC-920

    im guessing, that after 25 years the drum cleaning blade has failed and this is the cause for the black copies
  5. Thread: PCR's

    by Scottb
    Replies
    7
    Views
    247

    Re: PCR's

    generally speaking we do here as well, but im not opposed to testing in a couple of machines to see the results....especially something with the lifespan of Kyocera pcr's:D
  6. Thread: PCR's

    by Scottb
    Replies
    7
    Views
    247

    Re: PCR's

    Thanks Phil, sorry for the late reply its been a bit busy today. Yeah I've done that and usually they work out well. I was just thinking about all those bubbled ones that we through away and was...
  7. Thread: PCR's

    by Scottb
    Replies
    7
    Views
    247

    PCR's

    is there anyone recoating pcr's anymore last one I knew of was PCRMike...but I think he is long out of business. I was wondering since these kyocera pcr's dont go the full life expectancy
  8. Replies
    15
    Views
    503

    Re: Firmware update for Canon IR ADV C5051

    they do from service mode
  9. Thread: kyocera 2540dw

    by Scottb
    Replies
    4
    Views
    261

    Re: kyocera 2540dw

    its best to replace the fuser, but often you can give that fuser exit sensor arm spring another wrap and it will get you by for a little while
  10. Replies
    66
    Views
    23,196

    Re: Kyocera - Fleet Services

    you can also start a warranty part claim...it will fail, but it will give you the dealer contact info, from there you can contact the service manager and ask to have it removed
  11. Replies
    4
    Views
    219

    Re: Advice on taking on an IR ADV C5045i

    s/Accessories




    The parts support period for the models/accessories
    listed on this page have reached their end date.


    Category
  12. Replies
    16
    Views
    1,672

    Re: Strechy feed tires

    I had a lady ask once if I could put some alcohol on a rag and leave it in her trash can on my way out the door...I had no plans on getting to know her better so I gave my alcohol bottle a good...
  13. Thread: Test Answers

    by Scottb
    Replies
    32
    Views
    5,478

    Re: Test Answers

    who needs the answers to an open book test...if you're that dense this may not be the profession for you....
  14. Replies
    2
    Views
    218

    Re: TaskAlfa 406ci. Installtion

    U952 should have setup and will walk you through the correct sims and order
  15. Thread: kyocera 3500i

    by Scottb
    Replies
    6
    Views
    255

    Re: kyocera 3500i

    you will have to remove the developer and the registration dust collector felt, and then the right side door and lower rear cover, the connector and two wire holders, and four screws holding the reg...
  16. Replies
    3
    Views
    193

    Re: Kyocera 3500i keeps giving J4101 error

    i would look at the clutch pack and the clutch on the vertical path roller just behind the clutch pack to see if the clutches are dropping rust everywhere. also the registration roller assy has the...
  17. Thread: F248 Question

    by Scottb
    Replies
    5
    Views
    409

    Re: F248 Question

    Thanks for the input ill check this out...
  18. Thread: F248 Question

    by Scottb
    Replies
    5
    Views
    409

    F248 Question

    has anyone had a F248 error that wasn't caused by a print job...

    I have a CS4551 that will occasionally throw one usually first thing in the morning...but not always.

    All known computers...
  19. Replies
    16
    Views
    1,208

    Re: Question regarding Kyocera MFP'S

    a screwdriver, canned air and a vacuum will be about all you will need, for most pm's. On the 02-03 series there are about 3 screws holding the back on and thats it. everything else is latched in...
  20. Replies
    8
    Views
    329

    Re: 7003i scans intermittent upside down

    I would also check, to make sure that those 2-3 originals weren't upside down...otherwise more than likely all of the stack would be upside
  21. Thread: Roller Cleaning

    by Scottb
    Replies
    28
    Views
    1,287

    [Misc] Re: Roller Cleaning

    liquid hand soap works well also either diluted or just straight out of the pump.
  22. Thread: Roller Cleaning

    by Scottb
    Replies
    28
    Views
    1,287

    [Misc] Re: Roller Cleaning

    WD-40 is a good temporary fix and is easy to find...you will need to replace the rollers eventually though like when using rubber rejuvenator
  23. Thread: Copiers Filters

    by Scottb
    Replies
    2
    Views
    283

    [Misc] Re: Copiers Filters

    they help dissipate ozone...taking them out and not replacing them can lead to health issues with some people.
  24. Replies
    7
    Views
    585

    M3550 not sending faxes, but will receive.

    So I have ruled out the M3550, I took a 1135 known to work and a simulator box connected the two and both worked. Neither would send when connected to the customers phone line, so I know it must have...
  25. Replies
    2
    Views
    477

    Re: A couple of Canon questions

    Thank you I am dealing with a middle man so the code must have been miswritten.
Results 1 to 25 of 256
Page 1 of 11 1 2 3 4