Search:

Type: Posts; User: Nachoman4life

Page 1 of 8 1 2 3 4

Search: Search took 0.20 seconds.

  1. Replies
    13
    Views
    535

    Re: Sharp MX-5141N firmware update

    if the HDD is missing its a 320GB 2.5 in, you can go up in size but not down.
    Is the sd card currently installed blue with a generic white sticker on it?
    Also removing and reseating the controller...
  2. Replies
    12
    Views
    723

    Re: Sharp MX-M753n

    and fuser web maint is a pain.
  3. Replies
    2
    Views
    354

    Re: Phoenix fusers

    I have used a 608fb in place of a 607fb, with no negative results yet, did it out of necessity..
  4. Replies
    13
    Views
    535

    Re: Sharp MX-5141N firmware update

    Just made my first 10 donation...
  5. Replies
    13
    Views
    535

    Re: Sharp MX-5141N firmware update

    VHI0MFP00043C is the part number for an OEM SD card for a MX541
  6. Replies
    3
    Views
    411

    Re: Sharp easy mode

    Edit the home screen, delete the easy copy/fax icons, move the regular copy icons back to the 1st screen. Edit home is in the action panel on the right hand side of the screen.
  7. Replies
    14
    Views
    1,583

    Re: Power Requirements

    Had a Sharp MX6240 running on a 120v20a circuit with very few problems , given it was a basic box, no lcc, or fin... just a H4 code every couple of months, delivery guys "pig tailed" it, actually...
  8. Replies
    16
    Views
    2,235

    Re: Interesting find: Msata cards

    have not tried to overwrite a failed msata, but will spinwrite a few when I have a chance, to see if its a hard fault, or just a read error...should we start a new thread.... Are the sharp msata...
  9. Replies
    20
    Views
    1,953

    Re: sharp mx-3140

    Laser power step up,clear the appropriate counter, and recalib. Historious effect. (spelling may be wrong)
    Lets say a new drum, takes 1w, to flip from + to -, 100k pages later it takes 1.5w to make...
  10. Replies
    20
    Views
    1,953

    Re: sharp mx-3140

    you may have a failing sd card then, they can do some weird stuff when they fail, Ive had a few SD and HDD failures (at the same time), a couple of them showing a boot loader failure, of the linux...
  11. Replies
    20
    Views
    1,953

    Re: sharp mx-3140

    Correct, it is NOT advised to flip any hardware switch while the machine is powered up, let alone hot plug or unplug any electrical connection on a sharp, or any mfp, IMOHO.
  12. Replies
    20
    Views
    1,953

    Re: sharp mx-3140

    Yes, the mfp pwb is on the left hand side on this family of machines, it is the pwb that the network plugs into. there is a micro dip switch on the upper left hand on the board. If looking behind...
  13. Replies
    20
    Views
    1,953

    Re: sharp mx-3140

    admin pw reset is one of the two micro dip switches on the mfp pwb, one takes you to screen calib and the other allows you in admin and service pw reset. the mx3070 series started the no admin reset...
  14. Replies
    12
    Views
    1,129

    Re: Sharp MX-3140n

    Most color restrictions are done under the authority group.
  15. Replies
    14
    Views
    1,811

    Re: MX 4070N stripping black developer

    Agreed, had a Mxb42cl bleed out the rear frame side, down to the 1st transfer... Heat and storage...
  16. Replies
    5
    Views
    595

    Re: Side seal Powder

    Vacuum side seals every time you disassemble a drum, if they don't vac clean, replace them, there is contamination, that will eventually wear the edges of the drum down..and cause dv pull.. have...
  17. Replies
    14
    Views
    1,811

    Re: MX 4070N stripping black developer

    One helpful hint, open the end of the the waste toner auger port of the drum, and vac it out during a pm. seen a few of them forming large toner clot buildups at the front frame side, that...
  18. Re: MX-5141N Depleted Cyan Developer After Replacement

    Emptying a mx310hb, or 510hb, waste toner container, is a bad idea.
  19. Replies
    11
    Views
    1,769

    Re: New sharp colors/ mx3070 / 3071 etc

    No a properly maintained 4110, style belts usually make full life.. 200k
  20. Replies
    11
    Views
    1,769

    Re: New sharp colors/ mx3070 / 3071 etc

    Agreed.. A web is needed, and the 361fb, was WAY more durable than the mx60X, series belts are..it's a shame on Sharps part..
  21. Re: MX-6070N makes a 1mm line only when scans.

    I would guess, scanner jitter, if the machine is in a dirty environment, if its copy only, clean the rails, both mirror bases ride on, and relube. Other than that we need a scan example.
  22. Replies
    11
    Views
    1,501

    Re: mx-m565n Cleaning blade flip

    Placement of the felt seals matters alot, if either are too far inside than they should be, blade flips will happen.
  23. Replies
    23
    Views
    1,998

    Re: MX-4070 slow first copy

    or double check fuser temp settings, (sim43-1) if some one had adjusted temps for plain down,(to help with paper curl) and did not adjust warmup and ready temps down too, there will be a delay...
  24. Replies
    41
    Views
    3,416

    Re: And the correct response is....

    Customer: Are you going to be able to put that back together again?
    Me: Im just the disassembly guy, the reassemble guy will be by tomorrow.
  25. Replies
    25
    Views
    3,191

    Re: Did you Serve? What Branch What MOS

    o7, to those who served, and then, for having to deal with the copier industry after their service.:) Had 2 uncles who were 82nd and 101st, late 80s to late 90s.
Results 1 to 25 of 187
Page 1 of 8 1 2 3 4