Search:

Type: Posts; User: hidius

Page 1 of 5 1 2 3 4

Search: Search took 0.26 seconds.

  1. Replies
    9
    Views
    360

    Re: iR Adv 5030i Error E0027

    usually with this error code especially if its showing multiple sub codes is to take out the whole drum/dev process unit and ITB unit. look inside towards the back you will see the 4 color hopper...
  2. Replies
    5
    Views
    451

    [Error Code] Re: CANON AVD 8585ii

    when you turn on the machine for the first time it will come with this error code. depends on which model you buy it will come with a registration key which you have to register on the canon lms...
  3. Replies
    7
    Views
    474

    [Error Code] Re: E061-0101 on Canon IR adv 6075

    have you replaced the primary charging assembly?
  4. [Jamming] Re: Canon ir5045 paper jams and wrinkles in fuser unit showing error ps39

    ps39 is the reverse sensor. sometimes the sensor arm will pop of its holder. the way to check and fix is to remove the delivery unit then you can access it from the top
  5. Replies
    4
    Views
    799

    Re: Enter Serivce menu

    DX series service mode:

    1. in standby mode, press the "counter" key. this will bring up a number pad
    2. press the "setting/registration" key
    3. press number "2" key
    4. press number "8" key
    5....
  6. Replies
    13
    Views
    1,467

    [Electrical] Re: Error code E003-0000

    if you put a different fixing unit into that machine and clear the error code does it work?
  7. Replies
    13
    Views
    1,467

    [Electrical] Re: Error code E003-0000

    this error code needs to be cleared in service mode.

    setting/registration > 2+8 > setting/registration > mode list > copier > functions > clear > err > press ok

    restart the machine
  8. Replies
    10
    Views
    1,959

    Re: IR A6575i III PAPER DECK FAILURE

    if you followed the installion instructions you would of came across that step to move the pressure plate across
  9. Replies
    1
    Views
    657

    Re: C5500 / 4500 hard drives

    from my experience you cant pre-load these hard drive on a machine and swap it to another machine it wont work. if you swap hard drive you have to format and re-load the firmware to make it work
  10. Replies
    8
    Views
    790

    [Electrical] Re: Missing FEEDER MENU on service mode

    the menu doesnt show because there is something wrong with the reader unit. is there power to the reader unit? doese the light come on when you close the adf lid?
  11. Replies
    5
    Views
    974

    Re: Canon iPF minimum print volume

    with the canons just leave them in sleep mode .. they will wake up every couple days to do a minor head clean and nozzle test
  12. Thread: 2318 miss feed

    by hidius
    Replies
    9
    Views
    1,168

    [Jamming] Re: 2318 miss feed

    try cleaning the feed rollers. but sounds like a tray 1 paper pickup solenoid issue
  13. Re: Canon ir3245 printout in not centered on A4 sheet

    try a different tray including multi-purpose tray. if still the same could be a registration clutch. MMI clear might fix it or make it worst
  14. Re: iPF825 Plotter+ M40 Scanner connectivity issue

    is the plotter set as the default printer? also when you install the scanner driver, only plug it in when it tells you to or else it wont detect the scanner. you should also have gotten a usb stick...
  15. Thread: Canon IRC2220

    by hidius
    Replies
    3
    Views
    781

    [Misc] Re: Canon IRC2220

    try updating the firmware. if still the same, format the hard drive and do the firmware. if still the same replace the hard drive
  16. Re: canon IRA C5255 vs IRA C5045 Finisher compatability

    it'll probably give you an error code
  17. Replies
    3
    Views
    410

    Re: Speed licence ir adv8505

    The speed licence will determine how fast the machine is going to be so the machine wont work without it. if they didn't send it as a card in a box then they may have sent it in an email.
  18. Replies
    5
    Views
    479

    [Misc] Re: Canon IR 3530 black Streak in paper

    pull out the dev unit. rotate the dev roller and check if the marks are on there. if there is, you should be able to clean it off using your finger nails. don't use sharp tools that will scratch...
  19. Replies
    4
    Views
    1,037

    [Error Code] Re: Remove Paper From Output Tray Canon C5235i

    when you remove the inner finisher you have to put back the stack full sensor flag which is removed during the installation.
  20. Replies
    6
    Views
    424

    Re: Grinding noise on ir3045

    looks like a gear in the hopper unit. take the dev unit out and vacuum the pipe where the toner comes into the dev unit. if that doesn't fix it then replace the hopper
  21. Replies
    8
    Views
    534

    Re: canon ir3225 black lines

    looks like the dev unit. pull it out and clean the mag roller
  22. Replies
    6
    Views
    424

    Re: Grinding noise on ir3045

    you can run a motor test and check which motor is causing the noise
  23. Replies
    17
    Views
    1,546

    [Misc] Re: can't print via LAN cable

    initialize the machine back to factory default and try again. that will get rid off any settings that maybe causing the issue
  24. Replies
    2
    Views
    623

    [Error Code] Re: Canon IR Adv 8105 error 067-0001

    buy a new one
  25. [Error Code] Re: I am getting "Clean Slit Glass" Error On a Canon Imagerunner 4225i

    you still get the message but its displayed on the bottom of the screen. the user setting is just to stop the annoying pop up box displaying every time you scan or copy
Results 1 to 25 of 113
Page 1 of 5 1 2 3 4