Search:

Type: Posts; User: Toner Boy

Page 1 of 13 1 2 3 4

Search: Search took 0.43 seconds.

  1. Thread: MX2700N

    by Toner Boy
    Replies
    4
    Views
    894

    [CQ] Re: MX2700N

    paper type, weight, improper setting for print media ?
  2. Replies
    9
    Views
    2,602

    Re: New memory chips for the MX 4071

    Any recommendations for the target eMMC chip to be used on these machines? Copied to an Msata but not go / no fit
  3. Replies
    4
    Views
    232

    Re: Sharp hostname printing

    IP method is obviously preferred and endorsed by Sharp as default install method.
    Under an IT managed network this is fine, but we install on many unmanaged small networks, where routers may get...
  4. Replies
    12
    Views
    690

    Re: Sharp MX-M753n

    Fuser drive unit. one-ways slip, causing paper to stuff behind transfer belt. If machine has over 500K replace it and save yourself the frustration of troubleshooting that thing.
    It's less than...
  5. Replies
    4
    Views
    232

    Sharp hostname printing

    Many may know this...but I did not and struggled for a while to get working, couldn't find correct info. MX-C402SC and similar.
    NetBEUI enabled under Protocol Settings (may be NETBIOS on later...
  6. Replies
    10
    Views
    1,387

    Re: Sharp mxc 402

    Inspect DV units. These machines run dirty if not given parts at PM time. Contamination will suck DV out of units Serious cleaning and calibration.
    Optics are a bitch to clean, but if dirty...
  7. Replies
    17
    Views
    2,687

    Re: sharp mx 453 light prints and copies

    I'm beginning to suspect ATC sensors in the DV units, having this problem a lot these days.
    I've checked DV ref (around 46, too low) with 25-1, then taken ATC sensor out and cleaned it, then ran sim...
  8. MX2610N DC Power Supply swap w/mx2640 ??

    Brown-out killed DC Power. No PWB in stock, anyone try this swap? P/N's are different for sure.
    All connectors are the same, I've hooked up most connectors to verify power restores but don't want...
  9. Replies
    3
    Views
    1,485

    Re: SC530-18 Functional Problem MP9003

    Nice - thank you guys. Machine only has 50K on it, so I'm expecting it was a connector issue and not defective fan.
    Will update if returns.
  10. Replies
    3
    Views
    1,485

    SC530-18 Functional Problem MP9003

    Issue with Tray 3 feed unit, just stalls every 10 pages or so. Swapped with tray 2 feed unit, and they both work (for now....).
    Tray 2 will also become useless until machine is rebooted, but only...
  11. previous firmware needed: M5163 - MS811 etc

    Upgraded to latest...big mistake. Looking for firm build with Engine version FDN.DN.E715-0 ? Believe its v E63.3
    Have what appear to be all genuine Lexmark toner here 24B6015 (5 of them), but now...
  12. Replies
    10
    Views
    2,396

    Re: Office 365 scan to email

    Tried it on MX-4110N just now, failed. SSL security set to high.
    This is popping up everywhere today...please post if you figure it out!
  13. Re: is there diff w/ AR M277 and AR M317 DV unit?

    pretty sure they will interchange, even as old as AR275 possibly (think we did that 1x)
  14. Re: Change developer unit message on MAC print driver

    Please update us with what supply item (assuming that's what triggered it) caused the driver message, if you find it.
  15. Mac LPD vs Airprint driver versions MX3640N

    A little dumb with MacOS, on older machines we had issues with 'rendering' jobs, having to power cycle and wipe queue, print as IMAGE seemed less that great workaround.
    On this machine, certain...
  16. Replies
    4
    Views
    761

    Re: MX M503N ADF Not Feeding

    may want to check the belt tension in back drive area for tension adjust
  17. Replies
    9
    Views
    1,238

    Re: Royal Imaging Toner experience?

    We only use generic color on machines close to us in extreme cases. Black, no big deal...but all generics dust more than the OEM so be prepared to clean up a lot more often.
    AND...the main charge...
  18. Replies
    6
    Views
    1,006

    Re: Sharp MX B402sc Fuser part

    For maintenance contracts I'm considering skipping those items and just replacing the upper/lowers. If you replace all items, you may as well buy a new unit - especially considering the labor that...
  19. Replies
    15
    Views
    5,000

    Re: Sharp MX-M365N Corrupt SD Card

    Techs are cloning the good SD cards to use as backups for quick swap. A very good idea.
    Take clones of all possible SD card configs. Don't know if you can do with Compact Flash cards as well,...
  20. Replies
    3
    Views
    1,271

    Re: DCP 770 with 042-327...

    UPDATE. ITB assembly works perfectly in another machine (700).
    But I've got no idea where to go from here. Connectors, wiring, PWB...
  21. Replies
    0
    Views
    290

    DCP 770 with 042-327...

    Started with 42-326. Cleaned patch sensor, cleaned IBT belt frame assembly, reset 741-105 to 0 (swear it was like 126 prior to reset?). Failed. Cleaned belt edge sensor, and reset 741-106 from 3 to...
  22. Replies
    3
    Views
    1,271

    DCP 770 with 042-327...

    Started with 42-326. Cleaned patch sensor, cleaned belt underside (teflon cover over patch coming off), reset 741-105 to 0 (swear it was like 126 prior to reset?). Failed. Cleaned belt edge sensor,...
  23. Replies
    11
    Views
    3,326

    [Jamming] Re: Sharp MX-M623 POD1_N

    Don't discount paper as a possible issue. We changed nearly everything mentioned and switched paper (same weight) and problem solved (753N). The paper they had been using may have been exposed to...
  24. Replies
    22
    Views
    8,296

    [Jamming] Re: MX-3070-4070-5070-6070N

    Hard to believe we're having to deal with this again, had same issue with 3501's and dummy punch mylar way back when. Total dejavu
  25. Re: MX M363 Light when coping off glass (scans look fine and print copies look fine)

    Be sure ID sensor in transfer area is clean
    Clean optics, including lens / CCD if possible
    Clean LSU window...these are getting foggy over time and may require full cleaning
    Full calibration
Results 1 to 25 of 313
Page 1 of 13 1 2 3 4