Print driver presets within the print driver. Some manufacturers allow you to save the presets to a folder. Once all presets are saved to the folder, the folder of presets can be copied to a server...
Type: Posts; User: qbert69
Print driver presets within the print driver. Some manufacturers allow you to save the presets to a folder. Once all presets are saved to the folder, the folder of presets can be copied to a server...
Pay Attention!!!
TLAVagabond * DLive
Sent from my SM-N950U1 using Tapatalk
A definite note that dirty/contaminated laser slit glass can create a "soft", meaning de-registered and lightened image due to the dust/toner "scattering" the write beam on the drum...
Any rubber feed rollers that are dusted with paper dust or glossed over that need to be cleaned with rubber cleaner???[emoji848] sometimes slippage can occur from dirty/fouled feed rollers!!! Can...
I've seen the "fade" or non-existent color happen if the dev unit of a particular color is not aligned properly with the drum so that the developer mag roller with toner on it can properly brush...
IDC sensor usually at the end of the ITB, just below it and above the registration roller. I've also seen them right above the ITB, right before the fuser...usually a solenoid actuated shutter...
Spot On!!! We had some 808's that had about 1.5 million copies on them that were misfeeding... took out feed units and where the one way bearings are, the shafts were polished SLICK!!! Slick shaft =...
Laptop <---Crossover Cable--->MFP!!! DERP![emoji2957]
Is the paper that's "jamming" glossy, heavy, brochure stock by chance???[emoji848]
Sent from my SM-N950U1 using Tapatalk
It's ALWAYS going to throw the "caution hot fuser" message!!! It's warning you that it's HOTTT!!! DERP!!![emoji2957] Use your Noodle!!! If it's "always jamming", check to make sure the paper medium...
Is it true black or is it process (C,M,Y) black??? Is there a sensitivity adjustment in the print driver to bias the detection either towards true black/grayscale or the opposite direction of process...
Do an error code reset during startup but instead of doing an error clear, enter the service code to access service and then go to clear all the settings & reset the admin password. Should...
See if autocad has a flatten before sending to print function...other than that I have no other suggestions. It all boils down to the end user knowing WHY their file is spooling so...
The image is multi- layered and not flattened...use a program such as Bullzip to flatten into a single layer PDF before sending to the printer...[emoji57]
Sent from my SM-N950U1 using Tapatalk
Possible fuser drive/power sense board issue I'm guessing...are you able to monitor for proper fuser temps???[emoji848]...just because thermistors are clean doesn't mean the fuser is driven to the...
Warming up....sounds like a fuser issue. Check to make sure fuser thermistors are clean...Additionally, might there be a fuser drive board issue??? Just thinking....[emoji848]
Sent from my...
CUPS Interface in Safari, type in URL field: "localhost:631" ...minus quotes, then change default settings when you chose that printer...[emoji57]...may have to enable CUPS interface in terminal ...
Does this finisher have a reverse roller that tamps the sheets into place for stapling??? Or is it the side guides not tamping the sheets into position???[emoji848] It's also possible that there's...
Did you check all CUPS print driver default settings in the CUPS server???[emoji848]
Sent from my SM-N950U1 using Tapatalk
Watch Review...[emoji57]
Borat 2 Review (Contains Spoilers!) - YouTube
Sent from my SM-N950U1 using Tapatalk
LOL! OMG![emoji23][emoji38][emoji1787]...might need to check that router!!! I've had an instance or two where the router put the mfp on a "public" status and the pc on a "private" status just for...
Just a Quick Question...is his PC domain controlled by a server? If so, you will need it to authenticate with the local machine and not the domain if possible. [emoji6][emoji1303]
Sent from my...
Check to see if the network location is set to public or private mode!!! Public mode will pretty much shut down ALL incoming ports!!! Additionally, try using hostname and if that doesn't work, use...
He probably changed his PC login password...therefore an authentication failure![emoji57]
Sent from my SM-N950U1 using Tapatalk
SMB is port 445 or 139 (CIFS, deprecated) & TCP/IP printing can be ports 9100 and such.[emoji57]
Sent from my SM-N950U1 using Tapatalk