Search:

Type: Posts; User: onetek

Page 1 of 12 1 2 3 4

Search: Search took 0.03 seconds.

  1. Thread: Device Cloning

    by onetek
    Replies
    3
    Views
    354

    Re: Device Cloning

    I use Linux so for me it's Firefox or Chromium and sometimes I have to disable adblockers or popup blockers for the download to start.
  2. Replies
    4
    Views
    417

    [Error Code] Re: MX2314 - NETWORK SCANNING

    I have a few 2640,3140,4101,4110... that smb scanning stopped working. Ended up using old Network Scanner Lite from Sharp which basically sets up ftp scanning...
  3. Replies
    5
    Views
    554

    Re: Okidata MPS3537 vs Toshiba E-studio 347CS

    We had trouble getting drums from okidata, so I had to reset a few to get copiers going. I made a tool for that. You need a couple feet of phone wire, a push switch and a 12 volts bulb.Hook the 2...
  4. Replies
    5
    Views
    1,116

    Re: OKI MC861+ Fatal Error 142

    Yes, this board is on the left side , standing in front of copier.
  5. Replies
    5
    Views
    1,116

    Re: OKI MC861+ Fatal Error 142

    If I remember , its part of the board on the left side. Did you check the motor in test mode, with and without drums? Couple of times I had this code on that copier, it was due to binding mechanism....
  6. Replies
    17
    Views
    3,543

    Re: sharp mx 453 light prints and copies

    had that on one 453 (400k) and two 363 (800k and 2800k). On the 453, replacing the dev unit fixed it, on the 363, i reset doctor blade gap to at least 0.4 mm, and so far so good for 2 pm cycles....We...
  7. Replies
    2
    Views
    1,101

    [Error Code] Re: MX-6580 L8-20 code

    I was getting those L8-20 on a mx6240n. Tried replacing boards, hdd, sd card, power supply, ....Then I noticed that this code came only after plugging the network back on.Sharp sent me different...
  8. Replies
    3
    Views
    883

    Re: OKI MPS3537 paper tray/frame piece breaks

    Try Plate Assy Base # 45268401
  9. Replies
    9
    Views
    1,340

    Re: OkiData MB760 (E-studio 477S/527S)

    Maybe too late, but try PN# 45061702 FRAME ASSY (TOP) ...(just checked on BPX Okidata).We ordered quite a few of those...much cheaper than PN# 45484601.
  10. Replies
    34
    Views
    10,970

    Re: OSX 10.14 Mojave + Sharp MX2310

    This is what we got from Sharp.
    Still, I wont hold my breath...
  11. Replies
    34
    Views
    10,970

    Re: OSX 10.14 Mojave + Sharp MX2310

    Same problem here with a MX4101N...
    Th.
  12. Re: Sharp MX M503N fuser web question and 25-2 dev calibration question

    re web: The previous tek used web units from 4101 series (MX-410WC).Thats what we do here. They have those "washers".
    Th.
  13. Re: Change developer unit message on MAC print driver

    If push comes to shove,
    At the end of the PPD file add the following line exactly as written:
    *cupsSNMPSupplies: False

    You 'll get rid of all the supplies related status messages this way.
    Th.
  14. Replies
    11
    Views
    5,542

    [Error Code] Re: F2-40 Errors on MX-354N

    I'm late to the party, but in case you still need it...
  15. Thread: Light Cq

    by onetek
    Replies
    10
    Views
    1,326

    Re: Light Cq

    Yeah on this series machines, toner should be pulled out for sim 25-2. Once or twice, we had to replace the complete dev unit as well as transfer to get back to a nice CQ. (one of our 363 is over...
  16. Replies
    6
    Views
    1,333

    Re: Okidata MB760 Blank pages

    Have you tried opening front door while printing so paper stops under the drum, so you can check if the drum has anything on it? also, check laser diodes.
  17. Thread: R.E.D. reader

    by onetek
    Replies
    1
    Views
    677

    Re: R.E.D. reader

    You need to get it from your sharp ssap account. Also the machine needs to have its email diag key .
  18. Re: Retrieve Scans from Hard Drive via network PC Sharp MX-2615

    It wont work on a 4101,5001 coz no NAS.... too bad.
  19. Thread: Sharp MX-M 363n

    by onetek
    Replies
    12
    Views
    1,523

    Re: Sharp MX-M 363n

    If setup for dhcp, then switch to a fixed ip to rule out any dhcp trouble.
  20. Replies
    4
    Views
    915

    Re: Scan to windows 10

    To scan locally, I always find it easier to setup scan to main hdd folder : Enable the NAS function under Network Settings .Also enable NBT/WINS from Security Settings->Port Control.

    Scanning:...
  21. Replies
    13
    Views
    50,370

    Re: OKI MC562 Error Code 134

    Remove clp4 board, turn it around, locate picofuse F501 in the upper left corner and place a trace of solder across terminals. We replaced about 25 boards under warranty, and for those out of...
  22. Replies
    22
    Views
    3,021

    Re: MX-M354N Undertoning

    I've had a couple throwing me that F2-40 code. It was worn out rear mag bearing...(replaced under waranty).

    Th.
  23. Replies
    7
    Views
    1,223

    [Error Code] Re: code erreur j-17 panasonic DP-8060

    Ok. Fait des copies en mode F3, avec tous les tiroirs ouverts, et la porte en avant aussi ouverte. Active les 2 sensors de porte pour pouvoir regarder le fonctionnement du rouleau de registration....
  24. Replies
    7
    Views
    1,223

    [Error Code] Re: code erreur j-17 panasonic DP-8060

    Est ce que ša jam depuis tous les tiroirs et bypass?

    Is it jamming from all the drawers?
  25. Re: Mx-m354N throwing developer + error F2-40 + jamming

    Maybe unrelated to your situation but a couple years ago we had a brand new mx-m354n jamming in duplex mode. We could not figure out why so we exchanged the copier. During our shop tests, we did 1000...
Results 1 to 25 of 289
Page 1 of 12 1 2 3 4