Search:

Type: Posts; User: bilyahn

Page 1 of 20 1 2 3 4

Search: Search took 0.42 seconds.

  1. Replies
    5
    Views
    155

    Re: MX M453 "Remove paper from offset tray"

    If I remember correctly the FN9 went to several different series machines and after installing Sharp recommended upgrading the firmware. Had a lot of odd issues that were resolved by a firmware...
  2. Replies
    8
    Views
    497

    Re: Sharp MX-4070 admin password

    In order to change the admin password on the copier you will need to open a service call with sharp. There is a post from a couple of years ago with the procedure, somewhat involved but have done...
  3. Replies
    7
    Views
    455

    Re: MX6070N not keeping network settings

    You didn't mention a firmware update? Might help. The NIC card is integrated with the main board so that would be my last choice. Did you try resetting the NIC and clearing memory with sim 67-17
    ...
  4. Replies
    5
    Views
    241

    Re: MX3140 Desk unit trouble with some trays

    Replaced both sensors in tray 2 and 3 paper feed units and that resolved the problem. Go figure!!

    Thank you for all of the help.

    Bil
  5. Replies
    5
    Views
    241

    Re: MX3140 Desk unit trouble with some trays

    Did the sensor check and found something interesting about tray 2. When you pull out the tray the CPED2 sensor activates but when you push it back in it stays activated. You can reset it in sim 17. I...
  6. Replies
    3
    Views
    392

    Re: sharp mx-365n phantom ADF misfeed

    I have had this happen with the SPPD5 sensor. It will stick and not return to it's home position, if you close the DSPF forcefully sometimes it will reset but that doesn't fix the underlying problem....
  7. Replies
    5
    Views
    241

    MX3140 Desk unit trouble with some trays

    This problem just started recently. Have a 3 tray desk unit attached to an MX3140

    Tray 4 (the bottom tray) works fine.

    Tray 3 will not register that it has paper, all sensors work but it will...
  8. Re: 11x17 pdf documents not printing correctly on MX-5071

    PDFs have a print feature that allows the document to choose the paper size. You have to uncheck this box in the print driver, not sure why but some PDFs have this box checked by default. Doesn't...
  9. Replies
    2
    Views
    203

    Re: MX-FN14 won't shift

    I have had an issue with the front side gate sticking so it does not go down fast enough when doing offset. Has a foam rubber pad to reduce noise and after time this will start breaking down and...
  10. Replies
    3
    Views
    210

    [Misc] Re: User Code Authantication

    #*C*

    You can also google it
  11. Replies
    3
    Views
    210

    [Misc] Re: User Code Authantication

    Sim 22-7 will give you the admin login default is normally 00000. Then you can turn off user authentication.

    Good luck

    Bil
  12. Thread: Batch Printing

    by bilyahn
    Replies
    2
    Views
    204

    Re: Batch Printing

    Only thing that comes to mind is that your user names are corrupted or missing. Might try inputting new user names to see if this helps with your batch printing. Have had difficulties with this on...
  13. Thread: E7-11 error

    by bilyahn
    Replies
    7
    Views
    365

    Re: E7-11 error

    That is correct. Do a firmware update and a white reference adjust and see where that leads. I have a unit that just randomly throws one of these only when they scan, very annoying.

    Good luck.
    ...
  14. Re: MXM5071 problems printing complete documents from remote workers

    Thank you, I found this setting yesterday, I was not aware of it before. It was actually turned off.

    Found out that one remote worker had a print issue that is causing all of this. Since there is...
  15. Re: MXM5071 problems printing complete documents from remote workers

    Why is it that the WSD driver has so many issues? I try to let them know not to use the WSD driver but it seems to have a way of always showing up and being the default whenever people are having...
  16. Re: MXM5071 problems printing complete documents from remote workers

    Good question and I do not have the answer. I will ask the client when I see them on tuesday. I'm not 100% sure if it is only 1 remote worker or all of them. Remote for this purpose are users logging...
  17. MXM5071 problems printing complete documents from remote workers

    Workers are trying to print documents from remote locations. Document will print a few pages and that is it, nothing else. No error messages nothing to tell the customer that the document did not...
  18. Replies
    6
    Views
    823

    Re: MXM5071 F2-78 and now dark copies

    Had the F2-78 error code on this unit twice and both times it was because of developer pulled out of the unit but the sensor itself was not covered, go figure. Funny thing was the images were still...
  19. Replies
    15
    Views
    2,262

    Re: Several Sharp generations having email issues

    I will try this but other locations with the same email are working (almost all of the ones working are on frontier's network, possibly the only ones that are working). I am thinking I have already...
  20. Replies
    6
    Views
    823

    Re: MXM5071 F2-78 and now dark copies

    I did see this TB and thought about installing the mylar. It's definitely something to consider but the sensor doesn't seem to be covered in toner at all.

    Thank you

    Bil
  21. Replies
    6
    Views
    823

    Re: MXM5071 F2-78 and now dark copies

    Okay so far I have replaced the following items

    Drum frame
    drum
    charge
    DV unit
    Developer
    xfer roller

    Reseated and checked all connections, ROMs are current. Put it back together and...
  22. Re: At what age does Sharp stop supporting machines?

    We are able to get parts for machines that are quite old, in the 15 year range in some cases, with out any problems. Every once in awhile Sharp will put out a bulletin that states that certain parts...
  23. Replies
    15
    Views
    2,262

    Re: Several Sharp generations having email issues

    There are a couple of reasons for not using your own email but it all comes down to confidentiality. That's why I liked the email account that we were using as there was no record of emails sent in...
  24. Replies
    6
    Views
    823

    MXM5071 F2-78 and now dark copies

    Going back to this one today. Installed about a month ago then 2 weeks ago it gets an F2-78 PCS sensor error. Unit had toner all over the rear side of the drum and transfer roller. Cleaned...
  25. Thread: AR 5120 error

    by bilyahn
    Replies
    1
    Views
    515

    Re: AR 5120 error

    Toner error. Are you using OEM toner? Take toner out shake it and put back in, cycle the power and error should go away. If not replace the toner cartridge. You can take the cartridge out and look in...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4