Search:

Type: Posts; User: GIUBOSS

Page 1 of 16 1 2 3 4

Search: Search took 0.16 seconds.

  1. Re: Xerox workcentre 75xx low speed fuser vs high speed fuser

    The two models have different codes (604K62220, 604K62230) but the assembly is the same, different suppliers put it for both models.
  2. Replies
    12
    Views
    219

    Re: Mpc4502a With single pass feeder sc700-00

    try to unhook it from the machine and shake it upside down.
  3. Replies
    12
    Views
    219

    Re: Mpc4502a With single pass feeder sc700-00

    have you cleaned all the photosensors and around them? All the rollers?
  4. Replies
    2
    Views
    141

    Re: MFX-2570 System Error 9000

    firmware or memory to check I think
  5. Re: Control panel stays dark on image runner 256

    Try to boot with all doors open.
    Control panel defective, ram defective, file system not loaded.
  6. Replies
    6
    Views
    240

    Re: KM magicolor 7450 startup fail

    I would worry before running normal boot ..., did you try removing the extra memory and putting the old parts back?
  7. Replies
    2
    Views
    81

    Re: Utax 3005ci etc Drums

    I agree with Phil, If you do a search you will find a supplier in your country. They are the same Kyocera, firmware, PCDU groups etc., excluding toners (different chips).
  8. [Jamming] Re: HP Color Laserjet 3700dn Jam type problem

    I think the distance is normal, did you also do a single duplex print?
  9. Replies
    12
    Views
    334

    Re: MP C4503 toner bottle will not come out

    To avoid breaking the toner attachment mechanism, it is recommended to disassemble the output tray (in the absence of a bridge or a stapler), located above the toner to access the hopper, otherwise...
  10. [Jamming] Re: HP Color Laserjet 3700dn Jam type problem

    Have you checked any flag sensors and solenoids? The fusing unit could also affect the duplex, how many prints did it make?
  11. [Error Code] Re: xerox 7346 machine makes noise but the display is blank

    Have you done this already?


    Power off the printer using the power switch located on the right front side of the machine under the Control Panel.
    Wait until the Touch Screen is blank and then...
  12. Thread: Tearing paper

    by GIUBOSS
    Replies
    8
    Views
    406

    Re: Tearing paper

    It seems that the sheet comes from above instead of from the paper drawer ....?! is it a duplex? Or the paper arrives rolled up because it is damp or poor and stops on the belts. Try if it does...
  13. Replies
    6
    Views
    240

    Re: KM magicolor 7450 startup fail

    The problem is old age. You tried to remove the memory that you added to see if she was the problem even if it was recognized by the machine.
  14. Replies
    6
    Views
    240

    Re: KM magicolor 7450 startup fail

    If you are not a technician I think there is very little you can do, however try to remove the ram in the electronics part and clean the contacts by rubbing them with an eraser or simply with paper...
  15. Replies
    2
    Views
    287

    Re: sc2022 fuji xerox

    I found this, hold numbers 2 and 8 (keypad) and POWER ON the unit.
    Enter passcode 885 to access service mode.
  16. Replies
    2
    Views
    117

    Re: xerox 6600 fuser reset

    I suggest you to disassemble the fuser unit following the connection from the connector at the end you will find the answer, even if I doubt there are reset chips on sale.
  17. Re: HP M880 unable to detect size from flatbed

    I think you should clean the internal section of the scanner, glass, photosensors, lamp, white detector.
  18. Re: Kyocera 3050ci and 3551ci Magenta problems

    Strange, if the drum units are new, the blade should clean the drum by turning it by hand, a minimum of friction should be there
  19. Re: Kyocera 3050ci and 3551ci Magenta problems

    all original supplies and even toner? charge unit? calibrate the transfer belt. Apply the black conductive grease to the tips of all four drum shafts. Check the cleaning unit discharge roller if it's...
  20. Replies
    1
    Views
    285

    [Error Code] Re: Hp mfp m72630 error c3-1414

    1) Check if the connector is damaged 2) update the firmware 3) probable defective chip, replace the unit.
  21. Replies
    1
    Views
    151

    [Misc] Re: Oce Plotwave drum nicks

    a long time ago I put the enamel on the chipped cylinders but they were selenium, I don't think it works on the current ones, the enamel has solvent substances that could damage it.
  22. Replies
    12
    Views
    415

    Re: Bizhub C284e lines down prints

    hello, 1) get at least one service manual to study, if you have to do technical assistance don't you think? 2) make a print with 100% coverage for each color (C, M, Y, Blk). Check the PM counters.
  23. [Misc] Re: Kyocera KM2560 Sponge under laser unit, rotting...

    better to replace it with another similar sponge provided it has the same dimensions (I think the one for insulating the windows is fine) but make sure that it sticks well. The utility is...
  24. Replies
    4
    Views
    225

    Re: Drum PCDU UNITS

    you cannot use black pcdu for colors, but you could use some separate parts such as the cylinder
  25. Replies
    11
    Views
    527

    [Misc] Re: MPC 3003 scanner section bend

    not an impossible task but certainly not an easy one. Send us some photos of the damaged part, which, in my opinion, should be dismantled and restored to its original form. I believe only you can...
Results 1 to 25 of 386
Page 1 of 16 1 2 3 4