Search:

Type: Posts; User: kenpio

Page 1 of 6 1 2 3 4

Search: Search took 0.06 seconds.

  1. Thread: jams

    by kenpio
    Replies
    8
    Views
    615

    Re: jams

    What solved this problem in the 4 models, was to take out the registration roller unit and to clean all four bushings of those rollers. Something held them up and only tray one would skew. Hope this...
  2. Thread: C300i

    by kenpio
    Replies
    10
    Views
    669

    [Error Code] Re: C300i

    Rant over.
    Sorry kenpio for using your thread and congrats for your success.

    No problem tsb!! I have had the same thing happen. They are reading from a script. Once and awhile you get a good...
  3. Thread: C300i

    by kenpio
    Replies
    10
    Views
    669

    [Error Code] Re: C300i

    Well here is the C-0002 machine. The CPU board did fix it! Had to go through the set up again, but there was not the side LCT and it did register the LCC tray three! So we are all set to deliver,...
  4. Thread: C300i

    by kenpio
    Replies
    10
    Views
    669

    [Error Code] Re: C300i

    Update on Number 2,
    Went to customer with a different fuser and we replaced. Did the same thing. We loosened some of the wire ties and checked connectors from the power supply to base board. Turned...
  5. Re: Biz Hub C224e with DF701- scan glass assy jam?

    You may have to raise the doc feeder a little bit. It may be too close to the glass and you may see on the copy that it make a little bump or squiggle.

    KEN
  6. Thread: C300i

    by kenpio
    Replies
    10
    Views
    669

    [Error Code] C300i

    Howdy Folks,

    Have two strange ones here. One is right out of the box and the other has been out for about two months or so.

    Number 1
    Right out of the box, setting the machine up and turn it on...
  7. Replies
    19
    Views
    1,422

    Re: C223 Paper jam in ADF unit

    In the third picture, the square whole, the black patch looks a little white. Use some scotch tape and clean that out. In picture 4, that flap flips down, right before the white bar, and there is a...
  8. Replies
    2
    Views
    543

    [Misc] C3110 Black Image Unit

    Have a customer that we sent a black image unit for them to replace last week. No too bad, easy to do. Today I get a call saying that the black image unit needs to be replaced. I go to the customer...
  9. Replies
    4
    Views
    396

    [Jamming] Re: C300i 30-03 Jam code

    There is only the two trays on the machine and it is only jamming when long edge feed is used 8.5x11. When we feed it short feed it runs good. It happens before the fuser and transfer. It paper is...
  10. Replies
    4
    Views
    396

    [Jamming] C300i 30-03 Jam code

    Hi Folks,
    We have a C300i right out of the box that jams. It does one sided real nice, when we go to use duplex, it may do one okay, sometimes, but it will never do two pages with a jam code of...
  11. Replies
    25
    Views
    3,002

    Re: Bizhub "4" series tip

    Just thought I would say, was at a customer and pulled this off the exit roller of a BH364e.

    44564

    KEN
  12. Replies
    25
    Views
    3,002

    Re: Bizhub "4" series tip

    Have had this happen quite a few times. Get it while it is still warm you can mold the toner and it hardens pretty quick. :)

    KEN
  13. Replies
    31
    Views
    4,423

    [CQ] Re: C454e cyan developer

    Yea, just took the drums, developers and transfer belt and had access to the ducts and vacuumed them from the front. :)
  14. Replies
    31
    Views
    4,423

    [CQ] Re: C454e cyan developer

    Just an update for this call. The black drum and the transfer belt were at 0%. So I replaced them and cleaned out the cyan air duct and that was a couple weeks ago. Called the customer and it is...
  15. Replies
    31
    Views
    4,423

    [CQ] Re: C454e cyan developer

    Okay folks,
    Went to the customer on Monday of this week and changed the cyan developer, because it was gone. So I ordered the HV board and the toner subhopper and said that I would be back. I got...
  16. Replies
    3
    Views
    645

    Re: BH558e and demo page

    WOW!!! That was easy!! Thanks!!!

    KEN
  17. Replies
    3
    Views
    645

    BH558e and demo page

    Hi people,

    I have a BH558e here and have a strange one. I think that it was mentioned here before but I cant find it. What I have is when we go to print out a test page from the utility, print and...
  18. Replies
    31
    Views
    4,423

    [CQ] Re: C454e cyan developer

    Thanks for all the responses. Just some input here. The drums and transfer belt and roller are way under the usage. Gas gauge is at about half to three quarters on all. There are no C-codes, just in...
  19. Replies
    31
    Views
    4,423

    [CQ] Re: C454e cyan developer

    None of the other drums or developers are over life. They are about half way through their nice little life. :)
  20. Replies
    31
    Views
    4,423

    [CQ] Re: C454e cyan developer

    Here is a sample of the half tone cyan.
  21. Replies
    31
    Views
    4,423

    [CQ] C454e cyan developer

    Howdy Folks,

    I have a couple of these C454e machines that are eating cyan developer units. One machine just yesterday has only 9000 copies on the unit. I replaced the drum and developer previous...
  22. Replies
    20
    Views
    1,148

    [Misc] Re: C458 with FK-514

    So I went to the customer and switched 25 to B0. Before I did this the customer said that it was printing slow. Would this help that? You were talking of weird problems. They did print after I did...
  23. Replies
    20
    Views
    1,148

    [Misc] Re: C458 with FK-514

    Yes I found it in the firmware pdf, it is just way at the bottom. I will pay more attention to this in other firmware updates. I will go to the customer and change this. I am happy that this customer...
  24. Replies
    20
    Views
    1,148

    [Misc] Re: C458 with FK-514

    No I did not... Is this important?
  25. Thread: BH1052

    by kenpio
    Replies
    9
    Views
    490

    [Error Code] Re: BH1052

    An update on this. It has been weeks since the last 2411! YIPPE!! I did clean the toner hopper sensor, it seemed to be caked a little. Have not had a trouble with that error. Now starting to get...
Results 1 to 25 of 143
Page 1 of 6 1 2 3 4