Search:

Type: Posts; User: Synaux

Page 1 of 20 1 2 3 4

Search: Search took 0.10 seconds.

  1. Replies
    8
    Views
    456

    Re: FS534 Exit Drive issues...

    Final update:

    I got the second drive exit assembly together. (JB-welded the pulley and promptly installed backwards again! :cool:). For some reason, the inner shell of the exit unit became...
  2. Replies
    8
    Views
    456

    Re: FS534 Exit Drive issues...

    Okay, I finally have one finisher fixed. The other one is just a matter of assembly. There are a few things that I will take pictures of the other unit in hopes that it will help someone else when my...
  3. Replies
    8
    Views
    456

    Re: FS534 Exit Drive issues...

    Well maybe I missed something, but I couldn't take the inner shell off of one side to work from.

    I also did the same thing and left half of it together.

    I actually didnt mind it too much...
  4. Re: C451 Bad color when print/copy, but self-test is perfect

    I was leaning to the MFPB, but never seen seen such a thing so... :rolleyes:
  5. Replies
    8
    Views
    456

    Re: FS534 Exit Drive issues...

    Okay here are my discoveries: the M9 runs off of 3.3v which is a standard output of a computer PSU. I hotwired a PSU to run constantly and supplied 3.3v to the motor and reversing the polarity did...
  6. Replies
    8
    Views
    456

    FS534 Exit Drive issues...

    HI all, I hope yall had a great Father’s Day!

    I got two FS534s that have “Exit Section” problems. First off, if anyone has any for sale for a reasonable price I will greedily buy any/all of them...
  7. [Misc] Re: BizHub C659- issues with a certain custom document size

    I assume you are an End User? Try saving as a PDF (or save as your favorite bitmap, etc) then print from anything other than Illustrator.

    This honestly feels like you are missing something in the...
  8. Replies
    4
    Views
    288

    Re: Bizhub c550 error c4501

    Do you have the Service Manual? If you need it, make a small (or large) contribution and I will send it to you, or someone else will.
    I do not have a PRCB nearby to look at, but I found it in the...
  9. Thread: Bizhub 920

    by Synaux
    Replies
    6
    Views
    621

    Re: Bizhub 920

    I am not !@#$ing on CTN admin (there is just one, right?).
    However, I really feel there should be at least one admin responsible for each section of the forum for this reason. (I have a nomination...
  10. Re: Biz Hub C224e with DF701- scan glass assy jam?

    I recently had one bend the back corner but only about 1/4" - 1/2" with a fairly low jams. After going through it several times and finding nothing that I thought could possibly be putting the...
  11. Replies
    8
    Views
    488

    Re: Platt Tool Case Pallets - Opinions?

    Hey blackcat, your inbox is full
  12. Replies
    10
    Views
    610

    Re: Bizhub Fuser Rebuilds

    I might have missed a cross-ref, but while you are completely correct, this does not appear to be the case with the bigger/faster 4/8 series machines. :)
  13. [CQ] Re: BH C284e Counter list/ list output shrunk, squashed, condensed

    I didn't even consider the flux capacitor in those things! ;)
  14. [CQ] Re: BH C284e Counter list/ list output shrunk, squashed, condensed

    Be sure to change the laser unit before you try anything else!

    In all seriousness, I am curious to find out what figure out :)
  15. Re: Discontinued Part FS-608 + Neutralizing Brushes

    No problem. I kind of figured that might be the case.

    Thanks
  16. Replies
    10
    Views
    610

    Re: Bizhub Fuser Rebuilds

    You mean in general? I know the part numbers are different. This leads me to the perhaps absurd: Is it possible to convert a 4 series fuser to work in an 8 series and/or vice-versa?

    For the OP, I...
  17. Re: Discontinued Part FS-608 + Neutralizing Brushes

    Hey buddy, you ever get a chance to check? :)
  18. [Misc] Re: what chemicals are you using to clean one ways on KM units

    Not a huge fan of IPAs (give me gas).


    I have ~10x 5 gallon containers of blanket wash in storage (I think it is varn - pm me if you want some - I cannot give this stuff away in these parts)....
  19. Replies
    8
    Views
    488

    Re: Platt Tool Case Pallets - Opinions?

    Really? The molded pallets might be better when newerish, but these old ones are crumbling. When I close the top, simple gravity is litterally making the top pallet fitments fall off even with no...
  20. [CQ] Re: BH C284e Counter list/ list output shrunk, squashed, condensed

    This is your one and only post and you.... lol just lol
  21. Re: Help. Konica Minolta Bizhub C759 double/ghost prints on 11x17 only.

    I have seen this happen on older series with thick paper only.
  22. Replies
    8
    Views
    488

    Platt Tool Case Pallets - Opinions?

    I have a Platt 800T case with C and B pallets. The molded pallet pouches/pockets are made out of polyethylene (I think) and are literally falling apart. Quite possibly the worst material for...
  23. Discontinued Part FS-608 + Neutralizing Brushes

    Part Number: 20AK 4210 0
    PAPER CONVEYING ROLLER /A

    Goes to the Stacker unit. There is only one roller per finisher. If someone has a few I will be happy to purchase them or if someone can give...
  24. Replies
    17
    Views
    2,764

    Re: Has anybody ever seen this before?

    Wow, I do not know the data-flow, but this has to be an I/O issue:
    Network, demo and config only glitching is odd--are you [or should ask can you--no idea] on this model print the demo/config...
  25. Replies
    51
    Views
    4,832

    Re: Bizhub c224E not putting anything to paper

    Sounds like a fun trip! :P
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4