Search:

Type: Posts; User: repn1999

Page 1 of 11 1 2 3 4

Search: Search took 0.10 seconds.

  1. [Jamming] Re: phoenix/griffin mfps mx-3050, 3070, 3550, 3570, 4050, 4070, 5050, 5070, 6050...

    It is image registration adjustment manual mode. It is a required step of mfp setup and I usually check it on service calls because a lot of machines we sent out weren’t done. 50-28 has been removed...
  2. Replies
    0
    Views
    302

    Sharp MX4070N Msata image needed

    Do anyone have a msata image for a Sharp MX4070N? I have a machine down that I would like to get back up asap. I have other images to trade if you need any. Thanks in advance.
  3. Thread: Sharp MX 4141

    by repn1999
    Replies
    3
    Views
    683

    Re: Sharp MX 4141

    first i would say sd card....if not that maybe replace the entire operation panel. I know this sounds wierd.....but I have seen these act where the screen was frozen but it would still print and the...
  4. [Jamming] Re: phoenix/griffin mfps mx-3050, 3070, 3550, 3570, 4050, 4070, 5050, 5070, 6050...

    did you guys happen to actually do the 50-10 adjustment for the trays when setting up the machines? also these machines are known for bad fusers. I have had to wrap the pod1 flag spring another wrap...
  5. Replies
    4
    Views
    1,880

    Re: MX-M365N issues - memory, SDcard

    address limit reached can be fixed by running 66-10
  6. Replies
    1
    Views
    427

    Re: PCL 6 Print Driver Question

    yes it matters if it is checked and the machine has a dsk. usually docs wont print or print blank if you have a dsk and it isnt checked. newer machines use a totally new data security method and...
  7. Re: Sharp MX-4112N - Change HDD hard drive to a new one?

    the job log could be the issue if he didnt have random e7-03 also.
  8. Replies
    4
    Views
    667

    [CQ] Re: mx4111n light black copies

    these machines are known for light black copies. common causes are.....not calibrating with a jig, ae mode not set to mode 1 in 46-19. dirty or bad density sensor or a bad black dv unit. also make...
  9. Replies
    3
    Views
    690

    Re: C4-00 on Sharp MX-1810U

    has anyone checked the power going into the mfp? if voltage drops below 110 at any point or ground to neutral is more that 2v that could cause it. also make sure firmware has been updated. there is a...
  10. Replies
    8
    Views
    939

    Re: Replace developer unit message

    you need to change out the developer in the units.....a guy mentioned just resetting the counters for the units without replacing the developer.....DO NOT do that. It will cause copy quality issues...
  11. Replies
    9
    Views
    1,072

    Re: MXM623 paper behind transfer unit.

    did you replace the fuser drive unit with the new style CFRM-1103DS54 ? there is a modified unit to resolve this issue listed in bulletin TT-121313_3. the one way gear and shaft length were changed.
  12. Replies
    10
    Views
    1,552

    Re: MX-3070N "Please Wait"

    we had one of these that was doing a similar thing...not being able to get to webpage and would not take any account code. formatted the hard drive and reinstalled everything and that resolved our...
  13. Replies
    11
    Views
    1,724

    Re: MX-3140 Light Washy Copies (Print/Copy)

    for what its worth....check to make sure the exposure settings for copy and print modes are on factory defaults and then recalibrate. I have actually had a tech with a similar issue who did a...
  14. Replies
    4
    Views
    514

    [Error Code] Re: MX2640 - E7-03 Error

    I recommend replacing both the SD card and hard drive together. We make our own sd cards using high quality sd cards which dont fail and use 500gb wd blue 2.5 hard drives as replacement drives....
  15. Replies
    4
    Views
    649

    Re: MX3110 sd card image needed

    same card. how can you send it to me
  16. Replies
    4
    Views
    649

    MX3110 sd card image needed

    does anyone have a image for mx3110? I have others I can trade. need asap/
  17. Replies
    8
    Views
    25,037

    [Error Code] Re: C4-00 on Sharp MX-2310

    there is also a bulletin about changing the plastic holder for the pwb to spread them further apart to prevent arcing and electrical noise leading to failure. Its a good idea to replace both anytime...
  18. Replies
    9
    Views
    1,012

    Re: Sharp 5111 black print problems

    There was an updated MC pwb for this issue in a bulletin...also affects the 5141. Looks like you already isolated it to the board but this was more of a FYI
  19. Replies
    24
    Views
    3,207

    Re: MX-3640 unable to access network settings

    I had this happen once and ended up having to wipe the hard drive on a computer using diskpart and make a new SD card and then bring the machine back up from like a double SD/HDD failure using em...
  20. Replies
    10
    Views
    1,386

    Re: MX-4070N slow out of trays 1-4 only

    check 50-10 adjustments for the trays. are the trays set to different paper types.
  21. Replies
    9
    Views
    9,802

    [Error Code] Re: SC3 Sharp mx-3501n F2-42

    There was a firmware update for false F2-XX codes for that machine. Are you using OEM sharp toner and developer or compatible. If using compatible you are creating headaches like this for the future....
  22. Replies
    3
    Views
    847

    Re: Firmware question

    You should just be able to reload the firmware using emergency update, and then he will need to reinstall the watermark and e manual firmware, then he will need to recalibrate the machine. If it has...
  23. Re: M503N intermittent F1-08 finisher code ???

    There is a bulletin (MFP-TB-473) for this error for the MXFN10 finisher which basically has you chance the stapler rotation shaft and bushing to the new style and then update the firmware as well as...
  24. Replies
    5
    Views
    1,643

    Re: NX-4110 scanning Checks

    you are running into counterfeit protection not allowing the job. basically it makes you scan/copy in black and white(Mono2) and at least 10 percent larger or smaller than the original. this...
  25. Replies
    3
    Views
    293

    Re: Sharp mX565 Smudging and toner dust

    I have seen this issue twice on the orion series machines. one would think it is the fuser.....but no. What fixed it for us was replacing the dv unit. the new units have been modded to this issue and...
Results 1 to 25 of 266
Page 1 of 11 1 2 3 4