Search:

Type: Posts; User: lazymangr

Page 1 of 5 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    6
    Views
    418

    Re: Toshiba E-256 Paper jamming.

    if you changed all that and still you get jams 1st check if the door not closing good. try to print while you press the door against the machine or clean the vertical rollers in the small jam doors...
  2. Re: Original left on glass or detecting A4 with no paper C368

    Looks like it was way off and was interfering with the ruler attached to the platen glass. Copied numbers from another machine and problem gone. Then I did a fine-tuning from there. Thank you all
  3. Re: Original left on glass or detecting A4 with no paper C368

    thank you all for the help and time.
    ok after all the procedures above and contacting konica hit a wall, i stumbled upon service mode menu-> machine -> scan area and comparing to other machine was...
  4. Re: Original left on glass or detecting A4 with no paper C368

    If I raise the adf on the right side enough that don't actuate the sensor it works but it's messy because it don't start the procedure to read the platen glass if there is paper. It only works as it...
  5. Re: Original left on glass or detecting A4 with no paper C368

    nah I am far from it. All boards that reference to scanning are replaced but no avail
  6. Re: Original left on glass or detecting A4 with no paper C368

    As I said I already replaced scanner board and lens board from other working machine as Konica suggested but it's the same thing. Tomorrow I will contact them again since there is no other option...
  7. Re: Original left on glass or detecting A4 with no paper C368

    Nop. No scanner board no lens board from other machine. Same thing.
  8. Re: Original left on glass or detecting A4 with no paper C368

    That's right it works if I remove the reed switch because it don't enable the paper size detection. But that's not right. I am now replacing ccd and scanner board to check
  9. Re: Original left on glass or detecting A4 with no paper C368

    It's a leasing return machine with low meter. Tried table 1 and 2. But table 2 is for machines with 2 sensors on the right. The only way that it works as supposed is with the platen glass removed....
  10. Re: Original left on glass or detecting A4 with no paper C368

    I used 2 different adfs platen glass and slit glass from other working c258 machines to check. I done all the sane procedures. Now I am in the insane spectrum
  11. Original left on glass or detecting A4 with no paper C368

    Hello everyone! i have a c368 with the original left on glass when i lower the adf. what i have done so far

    the machine has only 1 original sensor for a3 in the right side of the platen glass...
  12. Replies
    33
    Views
    20,669

    Re: Bizhub C364e Jam Code: 20-02

    I think it needs thickness more than 1 paper. Try fold it 2 or 3 times
  13. Replies
    22
    Views
    1,533

    Re: 4e and 8 series drum unit

    yeah i am aware of that. i just ask if there are parts so i can do it in my office and just go to customer and plug and play instead of swapping the covers on field
  14. Replies
    22
    Views
    1,533

    Re: 4e and 8 series drum unit

    hey. have anyone found spare parts for the color drums holder-spacer so i can add black drums on color unit but build them in the office and not in customers office?
  15. Replies
    1
    Views
    450

    c3100p intermittent dark black pages

    hello all !
    a customer got c3100p with 36k total counter. called for total black page on print. on visit i test printed counters etc and saw the page total black like 200 halftone and you could see...
  16. Replies
    2
    Views
    1,056

    [Misc] Re: Toshiba ES167

    probably faulty ethernet addon card. 1st try open the machine with *+1+3 or #+1+3 if they dont work try remove the ethernet addon card from behind. firmware wont do much

    those codes resets the...
  17. Re: 25% Copier/ Printers Tariffs in the USA begin Friday May 10 2019 12:01 AM.

    imho i dont think that cheap products made in china for big companies are a china problem. they tell to the chineese factories what to build in what quality. they can make the same crap even if the...
  18. Re: Konica Bizhub C258 RedBlue Lines When Copying

    the real question is: how did this happen after 1.5 years?
  19. Replies
    0
    Views
    1,498

    epson xp-530 waste ink reseter needed

    as the title says epson xp-530 waste ink reseter needed. i got the epson adjustment program for some other models but cant find it for this model all are for sale. anyone got it?
  20. Replies
    2
    Views
    647

    Re: toshiba 457 - 357 printing slow

    firmware level?
    the latest as of 2 weeks ago (dont remember the version but was the latest available on toshiba)

    what print driver?
    tried both ps and pcl

    how is it set to spool?
    tested all...
  21. Replies
    2
    Views
    647

    toshiba 457 - 357 printing slow

    hello! title might be misleading but here is the problem.

    on a customer i installed a 357 copier but after some days they started to complain about speed issues on printing. i replaced with 457....
  22. Replies
    5
    Views
    868

    [Electrical] Re: Close front cover studio856

    hello! where you read to change power supply?

    check that the right side door closing properly of if there is any part broken that actuates the switch to detect that door is closed. its like a...
  23. Replies
    6
    Views
    1,837

    Re: cleaning product for rollers

    i mostly use acetone. works everytime
  24. Re: Help please, for the toshibae e-studio 355 firmware.

    i had the same problem when i updated the scanner with wrong firmware. you will need scanner update jig you cant fix it without it
  25. Replies
    12
    Views
    1,862

    [CQ] Re: Toshiba Estudio 757

    looks like erase led not conected. but check also the mylars on both ends of developer if its torn or has a small hole and/or doctor blade if its in spec space
Results 1 to 25 of 106
Page 1 of 5 1 2 3 4