Search:

Type: Posts; User: blackcat4866

Page 1 of 20 1 2 3 4

Search: Search took 0.13 seconds.

  1. Re: Could this be a damaged transfer belt?

    One more thought: You said that you were using Thick4 media type ... on 80 gsm? Incorrect heat setting too hot OR to cold will produce the same effect. If you're using 80gsm try Plain paper media...
  2. Re: Could this be a damaged transfer belt?

    Transfer belt cleaning issues typically do not look like this, and typically stay the same from pg1 to pg30. To be sure though, just pop the door open sometime around pg 25 and take a look at the...
  3. Re: Could this be a damaged transfer belt?

    To me, this look like toner built up on the heat sleeve. This can happen if the temperature is not high enough for your stock ... or if your stock is too heavy for the Thick4 setting. It's simple...
  4. Replies
    13
    Views
    273

    Re: TA-3551ci - J4401 jam code

    With hemostats squeeze at the area indicated by the arrows. The center tube will slide out. pay attention to the order that the parts go together:

    49491

    I would stock at least (6) clutches....
  5. Replies
    2
    Views
    62

    [Error Code] Re: KYOCERA TASKALFA 8002i

    Can you get the error to clear temporarily? If yes, enter service mode > U030 and run the developer motor. If it does not run, you might have a bad developing motor. Very similar motors are used in...
  6. Replies
    5
    Views
    356

    Re: HP-T520 24"

    I recommend to all ink based plotter users that the need to run at least 12 square feet per week minimum of full color image. Less than that, and your head will slowly clog up. If you think about the...
  7. Replies
    13
    Views
    273

    Re: TA-3551ci - J4401 jam code

    These same Daiken clutches are used on a wide variety of machines. There are heavier duty versions of this same clutch in the KM-8002i. And almost identical clutches in some Toshibas. Like rollers,...
  8. Replies
    13
    Views
    273

    Re: TA-3551ci - J4401 jam code

    Cleaning helps ... but by the time you see the rust they're done for. In an emergency when I only had say 4 of the 6 clutches I really needed, I have disassembled, cleaned all the parts, and...
  9. Re: KM-4800w - Operation Panel Display issue

    All the fans? Even the fans inside the print server CPU case?
  10. Replies
    5
    Views
    178

    Re: e-studio 307 hard drive install

    Congratulations. Loire 2X are notoriously slow booting back from a firmware update. At one point I called another tech because 08 mode had not yet come up after 25 minutes. He said to wait another...
  11. Replies
    13
    Views
    273

    Re: TA-3551ci - J4401 jam code

    Definitely clutches. The rust will be a dead giveaway. =^..^=
  12. Replies
    14
    Views
    1,463

    Re: Bizhub C368 No Matching Paper Size

    I had quite a hard time with this on bizhub PRO950s at a school district. The print driver drop down for size listed the 'W' wide paper sizes at the top of the list, and waaaayyy down at the bottom...
  13. Replies
    4
    Views
    130

    Re: kyocera p3150 image quality

    I've seen this before, but don't remember what I did. =^..^=
  14. Replies
    5
    Views
    178

    Re: e-studio 307 hard drive install

    I'm surprised that 3C > format wasn't enough. Yes 4C next.
  15. Replies
    6
    Views
    116

    Re: I'm new in the forum

    Welcome! =^..^=
  16. Replies
    5
    Views
    178

    Re: e-studio 307 hard drive install

    If I read that correctly, you went wrong when you tried to use the data on the working hard drive. Each machine has a unique encryption key, and cannot read data from another machine's drive.

    So,...
  17. Replies
    4
    Views
    130

    Re: kyocera p3150 image quality

    Maybe knock-off toner? =^..^=
  18. Re: Using D-FC65 developer in e5506AC machine

    I'd say that your odds are good. I'd go for it. I don't think that it has an EEPROM that might detect a mismatch.

    @Phil: This machine is kinda unique. When you do a developer change on one of...
  19. Replies
    2
    Views
    81

    Re: Why so many photosensors?

    I can contribute a little.

    You don't specify a manufacturer, but each manufacturer is consistent in its own way.
    Toshiba, for example, has only two or three basic paper sensor types in any...
  20. Re: HP T1600 Wide Format Plotter needs to be moved downstairs

    A few months ago I had a T2530 that the enduser moved up 3 floors of stairs (without telling us). The first thing they noticed was ink running down the left leg. A week later enough of that ink...
  21. Replies
    9
    Views
    255

    Re: Kyocera 4501i Dumping Toner

    It's not a cure, but definitely prolongs the interval. =^..^=
  22. Replies
    9
    Views
    212

    Re: Konica C224e reboots, SSDB?

    AFAIK it comes fully loaded. =^..^=
  23. Replies
    11
    Views
    553

    Re: 308 - Fully black prints

    If it was overtoning you would have edge voids. Concentrate on charge. =^..^=
  24. Re: Samsung CLX-6260FW printer prints blank pages.. most of the time

    Remove the glass, and use the drive drum to move the scanner through it's full travel. It should move smoothly. Are the cables crossed over on the drive drum? It's a common mistake to grab the mirror...
  25. Replies
    11
    Views
    553

    Re: 308 - Fully black prints

    Back in the analog days, yes, high voltage loss gave blank images. But at the advent of digital copiers, high voltage loss presents as black images and no voids. Digital copiers charge the drum...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4