Search:

Type: Posts; User: sparkycivic

Page 1 of 6 1 2 3 4

Search: Search took 0.08 seconds.

  1. [CQ] Re: Kyocera 3212i Sporatic Lines & Blank Prints

    change the charge roller, or entire drum kit - it's arcing.
  2. Replies
    2
    Views
    258

    Re: TA-4551 CI Image Distortion FYI

    at regular speed, the interval was 71mm, of course matching nothing in the book.
  3. Replies
    2
    Views
    258

    TA-4551 CI Image Distortion FYI

    I just finally got to the bottom of it...
    After 1 whole day of changing parts, it ended up being the engine board.

    Printing looked like the attached PDF

    There were 2x c4300 in very recent...
  4. Replies
    2
    Views
    230

    [Misc] Re: TA 250 ci image problem

    the main charge output is shorting out, shutting down the hv board. check all springs, paths and contacts of the HV outputs and charge coronas/grids
  5. Replies
    14
    Views
    1,065

    [Jamming] Re: 3051ci Jam 4019

    What happens if you run regular paper using "Card Stock" settings... if it jams, then it's a timing problem. If it doesn't jam, then it's a mechanical issue.
  6. Replies
    14
    Views
    1,065

    [Jamming] Re: 3051ci Jam 4019

    I'm thinking theres a weak clutch in the conveying (middle) drive section. Any rust back there??
  7. Replies
    5
    Views
    455

    Re: Kyocera M6535 vs M6635 drum issue..

    clean or replace the trans belt, it's dropping junk onto the drums which ruins the cleaning blades.

    give the belt a shake while vertical(with cleaner at top), i bet stuff falls out.

    The...
  8. Replies
    6
    Views
    543

    [CQ] Re: Problems with TR-8550 Transfer assy

    For us, actually so far so good, had a couple of early machines code with transfer cleaning motors while they were still young, then zero since. I haven't seen a torn belt ever, except for the stupid...
  9. Replies
    7
    Views
    700

    [CQ] Re: Waste toner 2 series.

    my quick check for the waste container drive/mis-shapen housing: grab the bottle and twist - if it moves by hand, the housing is borked. if it's tight, pull the main drive pack and go through all the...
  10. Replies
    2
    Views
    321

    [Misc] Re: Kyocera cs-305 dp-470 doc feeder.

    is the noise coming from the rear or another area?
    I've had some of these and others make noise where the velcro pad at the front left corner degrades, then the platen cover sags, and either...
  11. Re: Kyocera Taskalfa 4501i Light Printing problem

    is the toner from Kyo?
    does it only affect black?
    how does u89 sample look?
    maybe give black developer a vigorous shake end-to-end and see if there's any effect. might be blockage in dv.
  12. Replies
    6
    Views
    530

    Re: M3540idn with a u01193 error

    perhaps you can try to limit the fax speed by disabling 33'600 in the setup menu? u01193 is a G3 fax receive error(the highest speed), where the voip codec might be causing errors with the connection...
  13. Re: Kyocera Taskalfa 4551ci / ghost printing

    that really looks like the transfer belt isn't cleaning well, and the residue is ending up on the secondary transfer roller where it will remain until the first sheet of paper passes, then sticks to...
  14. Replies
    6
    Views
    1,233

    Re: J0107, C6220, C6320 Taskalfa 3252ci

    Another update: denied further troubleshooting efforts in lieu of machine engine replacement(upgrade excuse).

    My last effort ended up being to have the customer ADD A LONG EXTENSION CORD to the...
  15. Replies
    9
    Views
    1,205

    Re: printing issues with kyocera machines

    When my customers get this picky, I get best results from just showing them how to adjust the driver on their computer to alter the colors and balance, and how to save/load that final product. They...
  16. Replies
    6
    Views
    1,233

    Re: J0107, C6220, C6320 Taskalfa 3252ci

    An update:
    Hotline advised to try a low voltage pwb, and also do long term power quality monitor. The C codes and J0107 are continuing, so the monitor will get placed as soon as I get my hands on...
  17. Replies
    6
    Views
    1,233

    Re: J0107, C6220, C6320 Taskalfa 3252ci

    I'm not having any fuser rotation errors, C6220 and C6320 are thermistor high temp errors. J0107 is Fuser temperature stabilization timeout, according to the manuals.

    I already replaced the...
  18. Replies
    6
    Views
    1,233

    Re: J0107, C6220, C6320 Taskalfa 3252ci

    what fuser rotation errors are we talking about??
  19. Replies
    6
    Views
    1,233

    J0107, C6220, C6320 Taskalfa 3252ci

    I'm running low on options for this one, and am wondering if anyone else has encountered fuser heating control problems with a 52 series color box so far?

    Background: This machine is a few years...
  20. Replies
    6
    Views
    683

    Re: 8002 fuser not resetting.

    One should never swap EEPROM-equipped items while machine power is on, counts and/or serials will be messed up. It's so tempting when no tools are needed, especially when troubleshooting!
  21. Replies
    3
    Views
    426

    Re: fyi 4002i dv drive

    They always seem good with the explanation... right until I leave.
    seems to be a lot of "after-hours staff" causing problems.
    Kyocera REALLY should label the doors. My label maker uses expensive...
  22. Replies
    3
    Views
    426

    fyi 4002i dv drive

    Here is a little story to enlighten someone in the future who uses the search function.

    I had a machine with complaint of occasional blank output.

    But first a little background;
    There was an...
  23. Replies
    9
    Views
    1,546

    Re: TaskAlfa 3252ci SQUEAKING

    It was the main drum/dv drive assy.
    The waste toner passages/auger are attatched to the front of this drive assy, and a new drive needs the old waste section moved onto it.
    It's actually...
  24. Replies
    9
    Views
    1,546

    Re: TaskAlfa 3252ci SQUEAKING

    our very first installed machine of this style engine (2552ci) had a nasty squeak from the rear of the device during the first two weeks, had to replace the drive pack assembly under warranty. I...
  25. Replies
    4
    Views
    630

    Re: Kyocera M3540idn black dsiplay

    I've had one new out of the box with ribbon cable that had one "finger" peeled back during insertion, and bad colors on display. inspect the ribbon cables for contact deformation.
Results 1 to 25 of 143
Page 1 of 6 1 2 3 4