Search:

Type: Posts; User: mloudy

Page 1 of 7 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    246

    Re: RED READER JAM CODES

    Small Sharp dealer. I searched IDNC Service for RED reader and got no hits. I assume it isn't available because we can use MICAS.

    MICAS is really useful for many reasons. I can't understand why...
  2. Replies
    2
    Views
    185

    Re: Machine Availability

    I think it the forcast is ugly for all OEMs regarding A4 equipment. At this time we are able to get all A3 models we have been ordering from Sharp. Some ship right away and a few models will lag...
  3. Replies
    4
    Views
    246

    Re: RED READER JAM CODES

    From MICAS on a MX-5051



    9/28/2020 1:14
    Main Body or Original Jam
    C1PFD_N1 (2C1)
  4. Replies
    4
    Views
    246

    Re: RED READER JAM CODES

    Do you still not have MICAS in Canada?

    If not it would be intresting to know it one of your machines could be registered in MICAS and data collected from it.

    I have seen weird jam codes showing...
  5. Replies
    10
    Views
    646

    Re: Lexmark cx820 error 179.82A

    There a way to boot up a Lexmark with a new board in it without "attaching" that board to the machine? That way if the new baord doen't resolve the problem you can then power it down and remove it to...
  6. Re: Are You Paying Attention!!?? - Why The Demand In Used Machines With China!??

    After years of silence I began to receive status message emails from a Sharp copier that we had sold/serviced but had been replaced by another dealer. The emails still looked like they were coming...
  7. Re: Are You Paying Attention!!?? - Why The Demand In Used Machines With China!??

    So they buy old copiers and say they will pick them up for free. Transfer them a couple of times around the country to the west coast and then put them on a container with a bunch of other copiers...
  8. Replies
    19
    Views
    737

    Re: Why do sales guys speak so loud?

    Throat punch sales reps and face punch service techs.

    On serious note I recently ran into the grandson of the owner of an auto dealership that was around up until about 20 years ago. It was a...
  9. Replies
    1
    Views
    118

    Re: Mx-m2614 err: failed to expand ARM9 prg.

    SD card failure. Replace the SD card. Not just any SD card but one from Sharp or a new one that has been programmed with the correct .imgc data. 16GB should work.
  10. Replies
    19
    Views
    737

    Re: Why do sales guys speak so loud?

    As more than just a tech I have been to OEM sales meetings and service training. VERY different volume level in the rooms. Go to a National Dealer Meeting and attend the after hours gatherings at the...
  11. Replies
    2
    Views
    225

    Re: SHARP MX-M260 fuser drive gear

    I think this has changed over to NGERH0090QSZ1

    #6

    50274
  12. Replies
    16
    Views
    1,111

    Re: Flaring blacks MX-3070

    Hate it when the littlest of things can kick our butts. Well done.
  13. Replies
    6
    Views
    425

    Re: MXC300P paper exit

    Using only 8 digits, 0301023X

    The first digit will be the year, 2020.

    The last digit will be the month, November

    9 = Sept
    0 = Oct
    X = Nov
    Y - Dec
  14. Replies
    6
    Views
    425

    Re: MXC300P paper exit

    If you post the SN someone can give you the production date. The date might even be on the SN plate.
  15. Re: Sharp ARM237 Code L6. Need LSU unit part #duntk0384rszz

    I have a new one if you still need it. Cheap.
  16. Re: Best method for importing/export address book and data from a 3640 to the 70 seri

    I would start with 56-2.
    Used to backup the data in the EEPROM.SD Card, and HDD (including user authentication data and address data) to the USBmemory.

    I am not certain if you would need to...
  17. Re: Copier shipping companies - trucking companies?

    We have used Wullf for years and never had any problems. We mostly send lease end machines back with them but we buy used equipemnt from them sometimes. Most of the transport is within Ohio.
  18. Replies
    8
    Views
    674

    Re: MX5070 Address book ERROR [3000]

    Do not run sim 62-03 (Used to check read/write of the hard disk) in the field. I ran a 62-03 in the shop on a machine with a history of HDD errors and it took more than 24 hours to finish.
  19. Replies
    9
    Views
    733

    Re: Konica vs Lexmark

    From our Lexmark Business Solutions Dealer lineup card. We have not sold any of the non-Lexmark manufactured engines.
    50030
  20. Replies
    9
    Views
    733

    Re: Konica vs Lexmark

    I would say the Lexmark XC9225, XC9235, XC9245, XC9255 and XC9265.
  21. Replies
    2
    Views
    263

    Re: Lexmark PartnerNet sites and edge

    If someone took the time to figure out how to make it work with Edge it would simply stop working after the next Windows update. I do not like or use Edge.

    Sorry not to be of any help.
  22. Thread: Direct sales

    by mloudy
    Replies
    12
    Views
    791

    Re: Direct sales

    I am always a bit uneasy when buying from a new source. If the rep has been trying to get my business for a few years and still stays in contact even though I don't buy I feel a litlle more at ease...
  23. Replies
    11
    Views
    733

    Re: The cold hard truth about outside sales

    When they say social media are they talking about you spending advertising dollars on social media websites or them making connections on their own social media platforms that they frequent?

    I am...
  24. Thread: Direct sales

    by mloudy
    Replies
    12
    Views
    791

    Re: Direct sales

    Along with hard to get new engines there is huge amount of products damaged by the trucking companies now. I would normally get one damaged engine every two years. I am now seeing two damaged engines...
  25. Replies
    4
    Views
    302

    Re: MX421 with broken Start Button

    A smart designer would have split the part of the pwb with the keyswitches from the LCD diplay. Very stupid design and I think most if not all new Lexmarks are made this way.
Results 1 to 25 of 169
Page 1 of 7 1 2 3 4