Search:

Type: Posts; User: Synthohol

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds; generated 20 minute(s) ago.

  1. Replies
    1
    Views
    154

    Re: konica minolta 951 service manual

    done.
  2. [Misc] Re: Poor print quality on Konica Minolta C454e

    lemme ask you, were entire brand new OEM units replaced or simply rebuilt?
    i ask because you said developer not developer unit which suggests only the powder.
    you also mentioned including the...
  3. Re: I need help how to scan from konica minolta c454e

    So after I "slept" on it, make sure the ntlm level is set to ver 1/2 or locked in 2.0
    It may be windows is refusing connection to a lower security level after updating.
  4. Re: I need help how to scan from konica minolta c454e

    check network properties and make sure file and printer sharing is on
    create a folder on the root of the drive called scans.
    add a local user called scans, password of Scanner01 (it passes most...
  5. Re: [Image Quality] Thin line won't go away on Konica bizhub Press C6000

    ah yes, i understand now :)

    as process of elimination i would swap the black and cyan DV unit and drum (tape the toner holes shut and leave the toner door open so it wont try to add) and see if it...
  6. Re: [Image Quality] Thin line won't go away on Konica bizhub Press C6000

    zoom in, its in the black bar.
  7. Replies
    2
    Views
    206

    [Misc] Re: Bizhub 454e firmware needed

    link sent, thanks for being a contributor!!
  8. Replies
    7
    Views
    500

    Re: c650 no print but good ping...

    Cross over cable has not been required for a long time.
    Just use a regular patch cable.
  9. Re: c3350 Shows jam at right hand door and FF FF code

    Tray 2 sounds like a paper size mismatch and the 11-xx in tray 1 just change the rollers and make sure the backstop for the paper actually helps push the paper towards the rollers when lifted.
    I've...
  10. Re: c284e with No Animation Guide Available issue.

    Sent him a pm
  11. Re: c284e with No Animation Guide Available issue.

    If you still get the animation message load it again and watch the screen for "complete" and reboot.
    The version should show in the row.
  12. [Error Code] Re: Develop Ineo +224 - Error C-E401 and faulty menu

    what do you mean by factory reset?
    initialization from service mode or running a reset firmware?
    if the latter, try entering in the correct machine and type from booting with a FW stick.
    good luck
  13. Replies
    2
    Views
    183

    Re: c554 no energy

    always close the front door?
    machine is discontinued and not supported, is there a reason you dont close the door right after powering it up?
    is this something that really needs to be addressed if...
  14. Replies
    9
    Views
    612

    Re: C654e error C-3102

    Error
    CD291 at power ON

    Root Cause
    New style CCD (p/n A2X0R72111) was installed without updating firmware to G20-K9. Also make sure there is a good connection to the CCD.

    ...
  15. Re: Bizhub c220 replaced drums with new units, magenta warning still on

    Not to be a dick but why a c220? It's an old boat anchor!
    Check the 3 gold pins that touch the drum chip. Prolly not resetting.
    We're they OEM new drums or did you just replace the cylinder and...
  16. Replies
    3
    Views
    221

    Re: BH-C-284e, weight in grams of developer

    A new dv unit should last 500-600k, is it not more cost effective just to replace it instead of faking a fresh life cycle?
  17. Re: Service manual & options bizhub press c6000/7000/8000

    sent you a PM ;)

    you have a red card, whom did you piss off? you only have 2 posts and none look worthy of dissension.

    if you contribute a few dollars ill "rep" you back up to green :)
  18. Re: BH-C-280 and C-284e, Paperpassage test limitations?

    Any pages from service mode or meter sheets do NOT increase the counter.
    Minutes of use however will accumulate normally to properly represent the state of consumables
  19. Replies
    3
    Views
    269

    Re: BH-C-3110, airprint

    AirPrint (Bonjour) setting is disabled


    Solution
    CAUSE: Firmware requires updating

    SOLUTION: Install the following firmware based on the model. The latest version of firmware,...
  20. Thread: c654e movie

    by Synthohol
    Replies
    2
    Views
    191

    Re: c654e movie

    PM sent ;)
  21. Replies
    1
    Views
    151

    [Dead] Re: CREO IC-312 System Software Reload

    Reference
    CREO has released Version 2.0 software for the IC-309 (compatible with bizhub PRESS C1070, C1070P, C71hc, C1060) and IC-312 (compatible with bizhub PRESS C1100, C1085) controllers....
  22. Replies
    7
    Views
    500

    Re: c650 no print but good ping...

    have you tried your laptop directly to it?
  23. Re: Strange smudges on printing backside in KM C258

    as a test load the paper landscape and try again, if the smudges move its something physical in the machine, if the smudges stay in the same spot its likely something in the image.
    just something to...
  24. Re: c3350 Shows jam at right hand door and FF FF code

    3.5.14 2152
    (1) Contents


    Trouble type
    1st transfer pressure/retraction malfunction


    Trouble code
    2152
  25. Replies
    9
    Views
    612

    Re: C654e error C-3102

    did you replace it with a new fuser or a used one?
    there is a new style fuser A2X0R71055 or later, i think they are up to 88

    Error
    C3102 error code may occur during fusing roller...
Results 1 to 25 of 499
Page 1 of 20 1 2 3 4