Search:

Type: Posts; User: copyman

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Thread: Thank you all

    by copyman
    Replies
    6
    Views
    173

    [Misc] Re: Thank you all

    It's good you found out while still young. A career change can be a good thing. I'm a few years away from retirement after 40+ yrs in the copier business and it has changed a lot over those years....
  2. Replies
    20
    Views
    601

    Re: Konica C258 settings problem

    Are you leaving front door open when trying to update firmware? It has to stay open during F/W update
  3. Replies
    4
    Views
    263

    [Misc] Re: Konica Minolta C458 Humming/Whistle Noise

    Not much is on and little output from power supply with doors open. If happening when doors open then I would look at a fan making noise.
  4. Replies
    5
    Views
    955

    [CQ] Re: Bizhub C451 print problems in thick mode

    Wouldn't be the transfer belt or roller if only one color is affected. If only one color than I would look at that color image unit being low on developer.
  5. Replies
    5
    Views
    955

    [CQ] Re: Bizhub C451 print problems in thick mode

    You might need a fuser unit. If you run a lot of thick stock the fuser units life is shortened considerably, especially with the older models.
  6. Replies
    3
    Views
    193

    [CQ] Re: DV711C C654 developer

    Copylite - Aftermarket, Compatible, and OEM Copier Supplies and Products
  7. Replies
    3
    Views
    193

    [CQ] Re: DV711C C654 developer

    Yes we use aftermarket developer in the IU711 all the time and works just fine. Most of the time we just add some developer to IU's that have crashed and most will recover. Of course if IU is at 0%...
  8. Replies
    10
    Views
    383

    Re: Bizhub C283 Jamming

    If 150k or less on meter I always just spray the reg clutch with electronic cleaner and then canned air. With clutch on machine, no need to remove. Lube the reg roller bushings and should be good to...
  9. Replies
    5
    Views
    297

    Re: BH-C-284e, my first rusty CL8

    Attached are both replacement versions, the correct way and the shortened version
  10. Replies
    10
    Views
    639

    Re: KM bizhub 283 - manual paper feed problems

    Agree! I've seen new parts & accessories really cheap for this old model but would still fix it.
  11. Re: Why are my magenta prints Faded in one side? konica c360

    Still looks like developer is low.

    What are the levels under state confirmation in service mode. I suspect the magenta will be off.

    Aftermarket toner or drum? You can easily swap drum with...
  12. Replies
    10
    Views
    639

    Re: KM bizhub 283 - manual paper feed problems

    It's most likely the clutch but if you change all those parts or the complete manual feed tray issue should be solved.


    Of course first make sure pick up roller is good
  13. Replies
    4
    Views
    197

    Re: konica minolta 224e fax problems

    See attached. Check marketing is correct & do fax initialization. Both in service mode. Make sure to turn main power off and back on after exiting service mode.
  14. Thread: Biz hub c425

    by copyman
    Replies
    12
    Views
    458

    Re: Biz hub c452

    A typo? The wrong model # is more than a typo. How about page count, direction of paper, what you have done so far, etc, etc?

    Get off that low horse and provide correct information! It will help...
  15. Thread: Biz hub c425

    by copyman
    Replies
    12
    Views
    458

    Re: Biz hub c425

    Even though you mainly deal with Canon the least you could do it provide an accurate model #. Sorry I refuse to even try and help without some very basic information. Model #, Page count, Direction...
  16. Re: Develop Ineo+258(Konica Minolta B. C258)tray 1 and tray 2 need a lot of power to

    I've seen where tray is really hard to open on the 4 series but not the 8 series... yet. It helps to put some light grease on the white piece that retracts when you pull on tray handle. Also have...
  17. Replies
    17
    Views
    461

    [Misc] Re: Konica minolta c452 light print at bottom

    I would start with at least the Magenta Image unit. Or split the IU open and clean corona, etc. Maybe add a little aftermarket developer.
  18. Replies
    13
    Views
    672

    Re: C258 Recycling Coil Broken

    How long has the original toner been in? Did you put original toner in when you installed new drum & developer as mentioned in your OP? It takes some time for the good toner to work it's way in. If...
  19. Replies
    17
    Views
    461

    [Misc] Re: Konica minolta c452 light print at bottom

    I would try removing and cleaning the laser PH. Could also be a drum problem even with 15K, especially if the drums are old.
  20. Replies
    13
    Views
    672

    Re: C258 Recycling Coil Broken

    What is the page count? Genuine or aftermarket toner?

    Keep in mind "any" over life consumable can affect "any" other color.
  21. Replies
    22
    Views
    960

    Re: Stains on copy model 308e

    After all the guesses hopefully the OP will report back with what it turned out to be.......
  22. Replies
    22
    Views
    960

    Re: Stains on copy model 308e

    Never had it on a "4" series so if the drum as suspected it's probably that damn PCR !
  23. Replies
    9
    Views
    428

    Re: Konica c280 crooked copy

    Did you make sure ADF hinge screws are tight? Try the adjustment on the right ADF hinge? Even though the ADF may look like it's "properly aligned" it may still need to be adjusted.
  24. Replies
    10
    Views
    485

    Re: C224e scan quality

    Remembered something else, before I did anything was troubleshooting making copies through ADF & off glass, I noticed when copying off glass scanner assy was scraping against rear frame when scanning...
  25. Replies
    4
    Views
    234

    Re: bizhub 361 error 3805

    With that older model it could be pwr supply. Check for cold solder joints and re-solder.

    How good is electrical where copier is & good ground? Is it on a good surge protector?
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4