Search:

Type: Posts; User: kuby

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    0
    Views
    100

    TASKalfa 4002i - C7490 & C6900 errors

    Have a 4002i machine throwing C7490 and C6900 codes but only when running 8 1/2 x 14 duplex copies. Have ordered a edge fan motor 302K994360 and hopes that it fixes it. Have run U037 and do not...
  2. Replies
    2
    Views
    249

    Re: Ecosys P2040dn, which driver for W10/64?

    WSD driver is garbage....
  3. Replies
    10
    Views
    711

    Re: M2540 series fuser problem

    Yes the sleep timers get reset by the customer. Need to check them.
  4. Replies
    5
    Views
    302

    Re: 4052ci popping noise

    Yea waste toner bottle hopper is ok it is the waste toner auger assy and the transfer belt auger. Both locked up.

    Thanks
  5. Replies
    5
    Views
    302

    Re: 4052ci popping noise

    Always used OEM toner.
  6. Replies
    5
    Views
    302

    4052ci popping noise

    There is a popping noise coming from the gear on the 302ND94013 PARTS BOX WASTE H ASSY SP gear. Is the box at fault or is the 02ND94224 PARTS WTB UNIT SP. Never had this before and I don't want to...
  7. Replies
    10
    Views
    711

    Re: M2540 series fuser problem

    Sorry wrong post
  8. Replies
    10
    Views
    711

    Re: M2540 series fuser problem

    Try stretching the spring in the fuser drive assy. Worked for me. After a while it gets week and will and turn the fuser, a new fuser will work for a while and then it starts jamming again.
  9. Replies
    2
    Views
    229

    Re: HPM477 what is this

    Looks like that is a Engine Test Page ?
  10. Replies
    3
    Views
    234

    Re: olivetti 4500(taskaalfa 4500)

    Maybe one leg of the power switch is bad, check the switch.

    Power source PWB ?

    *****************************************
    Like Copierstud said.
    If forgot we have one that the main board to a...
  11. Replies
    3
    Views
    323

    Re: f000 error kyocera 3500

    F000 Communication error between Main PWB and Operation PWB

    Main PWB

    1. Turn the main power swtch off and after 5 seconds, then turn power on.

    2. Check that the wirings and connetors...
  12. Thread: Additional memory

    by kuby
    Replies
    5
    Views
    256

    [Misc] Re: Additional memory

    I just looked and it showed the memory?
  13. Thread: Additional memory

    by kuby
    Replies
    5
    Views
    256

    [Misc] Re: Additional memory

    Amazon. 855D200662

    1GB

    Keystron 1GB Printer Memory Upgrade for Kyocera 855D200662 at Amazon.com
  14. Replies
    6
    Views
    564

    Re: Pinpoint scan issue (Taskalfa 4052)

    Have you tired trying to connect using the computer IP address? Pin Point may have lost its mapping. You can also try restarting both the computer and the copier.
  15. Replies
    0
    Views
    232

    General Technical Bulletin #99.

    Anyone have this bulletin they could share or tell me where to find it on Kyocera's site. I have looked and can not seem to locate it.

    Thanks


    ***********************************************...
  16. Replies
    5
    Views
    312

    Re: ECOSYS M6635cidn fax errors

    It is a Spectrum Fax/Modem connected to the internet and then to the machine and faxes with a digital signal.
  17. Replies
    5
    Views
    312

    ECOSYS M6635cidn fax errors

    We have a M6635cidn that keeps getting U01011, U01026 and U01056 errors when faxing. It is hooked up thru a Fax Modem and the internet.
    The setting are:
    Port 1:
    Communication Control 1:
    TX...
  18. Replies
    11
    Views
    931

    Re: TA 3551ci/fax paper settings

    Had a problem with a 5054ci series doing something similar. Kyocera had me set tray 1 to auto/plain and inch and told the customer to tell everyone not to change that tray setting. Kyocera told me...
  19. [Misc] Re: TA 4002i has a continuously running exit unit until it goes into sleep mode

    Yes Kyocera recommends disabling IPV6 also.
  20. Replies
    3
    Views
    279

    [Dead] Re: IR 7095 NETWORK PROBLEM

    I would say the network card it toast. Was it on a surge protector that protected the power plus the network card?
  21. Replies
    3
    Views
    297

    Re: Lexmark X925 - FTP Scan setting

    Thanks I am just trying to scan to their computers on their network. I know the IP address of each one, they scanned one time and then nothing. Is there a manual on how to set this up?

    Thanks
  22. Replies
    3
    Views
    297

    Lexmark X925 - FTP Scan setting

    Customer ask me to work on this machine as the people that sold it could never get the FTP scan to work. Logged into the copier and noticed that the IP address they were trying to scan to was wrong,...
  23. Replies
    7
    Views
    542

    Re: Kyo Service Portal

    I don't know. All I know is that I was having trouble with IE using the Portal and KFS and Kyocera told me to use Chrome ? Been using it ever since.

    Maybe it was just me.
  24. Replies
    7
    Views
    542

    Re: Kyo Service Portal

    Use Google Chrome. Have problems with IE.
  25. Replies
    2
    Views
    249

    Kyocera TA 4054ci - brand code ?

    Setting up a NEW Kyocera TASKalfa 4054ci and it is asking for a Brand Code ? The document they sent with the Activation code does not show a Brand Code. Where do I get this or does someone know what...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4