Search:

Type: Posts; User: Cantechman

Page 1 of 8 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    10
    Views
    573

    Re: bizhub C250i foggy backgroud printout

    you can try this:
    change switch 153 bit 6

    under pcl driver:
    quality tab/quality adjustment/other/turn pure black off
  2. Replies
    29
    Views
    2,474

    Re: bizhub c300i jam tray 1

    Hasn't been issue since it was replaced.
  3. Replies
    5
    Views
    470

    Bizhub c250i squeaking noise

    I have a c250i with only 20k, it randomly will make a squeaking noise (like a bad bearing type noise) for a minute or so while the machine is not being used, happens very randomly. I couldn't get to...
  4. Replies
    29
    Views
    2,474

    Re: bizhub c300i jam tray 1

    There is a procedure for that particular clutch in the manual. you have to open the "box" not remove the board itself.
  5. Replies
    29
    Views
    2,474

    Re: bizhub c300i jam tray 1

    I never really read what it's function is other then helping transport the paper but's only related to tray one and the bypass I do believe.
  6. Re: konica minolta c360i tray one jam code 1105 also internal error erratic code

    If he changed the whole pickup section and the fast clutch only thing left would be something in the registration section or the baseboard from what i recall.
  7. Replies
    29
    Views
    2,474

    Re: bizhub c300i jam tray 1

    It wasn't that bad, the hardest part is just opening up the baseboard box, I'd say start to finish it took 45 min.
  8. Re: konica minolta c360i tray one jam code 1105 also internal error erratic code

    I'm an old dog as well started in late 90's when there was no such thing as a multifunction machine lol.
  9. [Error Code] Re: Bizhub 4050 Prompt A Trouble Code E301(000.00)

    If the error code does not appear, plug in any applicable cables or add-ons one at a time, waiting at least 30 seconds between any additions. If the code appearswhen the network cable is plugged back...
  10. Re: konica minolta c360i tray one jam code 1105 also internal error erratic code

    Have a look at my thread from a few weeks back. My machine was brand new as well.


    bizhub c300i jam tray 1
  11. Replies
    17
    Views
    879

    [Jamming] Re: Bizhub 25e keeps jamming documents

    It's been a while, but I think it's the one i have attached circled. It would randomly stick in the up position.
  12. Replies
    17
    Views
    879

    [Jamming] Re: Bizhub 25e keeps jamming documents

    Check the actuator that hangs down. I had one that would randomly stick up in place when it was suppose to move back in position after the sheet was fed. Make sure if moves freely, push it up a...
  13. Replies
    3
    Views
    239

    Re: c3850fs screen blank, machine cycling

    I would start by disconnecting the network and fax cables, I would try and boot into service mode holding down the power button, and if you can update firmware and format the HD. If that doesn't help...
  14. Replies
    29
    Views
    2,474

    Re: bizhub c300i jam tray 1

    The problem was the fast clutch (cl10). It's behind the base board. Once replaced and tested it worked fine.
  15. Replies
    29
    Views
    2,474

    Re: bizhub c300i jam tray 1

    It seemed as though it did for a week or so, must have been a coincedence.
  16. Replies
    29
    Views
    2,474

    Re: bizhub c300i jam tray 1

    it seemed to initially but the customer called back a week later and said it's happening again.
  17. Replies
    29
    Views
    2,474

    Re: bizhub c300i jam tray 1

    [QUOTE=Bix;1680974]Where the paper stop?[/

    Sometimes it doesn't leave the tray, other times it does so no specific place. one or 2 prints seem to be fine it's multiple prints where the issue...
  18. Replies
    29
    Views
    2,474

    Re: bizhub c300i jam tray 1

    I have another complete registration unit to try. It happens intermittently so it's a little difficult to diagnose. If that doesn't work i will try the paper feed roller fast clutch and then finally...
  19. Replies
    29
    Views
    2,474

    Re: bizhub c300i jam tray 1

    Yes did both.
  20. Replies
    29
    Views
    2,474

    bizhub c300i jam tray 1

    I have a new C300i install with intermittent jam codes 1102 and 1105 from tray 1. Everything related passed the load check. I replaced the whole feed section and it seemed ok temporarily. Any ideas...
  21. Replies
    9
    Views
    1,730

    Re: Bizhub 4050 freezes/locking up

    I had a bad control panel just 2 weeks ago on a 4050 that did basically the same thing. Randomly froze up. Replacing it fixed the problem.
  22. Replies
    11
    Views
    600

    Re: C3850FS problem

    I have used hard drives for different Konica Minolta copiers before and they have worked fine. Not sure about a generic HD but at this point you don't have anything to lose. You would just have to...
  23. Replies
    31
    Views
    2,336

    Re: Automatic reset bizhub 4050

    It might be the heartbeat setting in CS remote care. It's turned on by default and can be set between 1-256 minutes. Check the number it's set to under Communication interval. If it's set to 9 then...
  24. Replies
    10
    Views
    763

    Re: bizhub 4020i crumpled paper

    It certainly looks like a fuser issue to me. If it's only missing the spring for some reason maybe you can find one in a hardware store to fix it.
  25. Replies
    2
    Views
    308

    Re: C3850 black screen

    C3850 display issue but won't print either



    This one too.
Results 1 to 25 of 176
Page 1 of 8 1 2 3 4