Search:

Type: Posts; User: Victor285

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. Re: bizhub C250 Keeps asking to remove and reinstall drum

    That's good. But you may want to be proactive and setup a plan to replace before you start experiencing more messages. Its a sign that the wiring has a break in it or bad connection. ..and its always...
  2. [CQ] Re: Bizhub 421 - Streaks in subscan direction

    Thanks for the quick followup, CraigW. I'll report back later.
  3. [CQ] Re: Bizhub 421 - Streaks in subscan direction

    Drum is 209,000

    Developer only
    36,000
  4. [CQ] Re: Bizhub 421 - Streaks in subscan direction

    If it is the drum scuff. Can you replace just the drum on these or do you also have to change developer at the same time? Service Manual says that you have to reset counter or you may get fogging or...
  5. Replies
    20
    Views
    4,920

    Re: Bizhub 250 trying to reset error code

    Doesn't matter now, as he replaced unit. :rolleyes: Trouble reset is timed with rather short window for resetting or it continues cycling. 3, 00000000. trouble reset, exit.
  6. Replies
    20
    Views
    4,920

    Re: Bizhub 250 trying to reset error code

    After you see dot on screen, press 3, then enter access code and enter / exit. You should either get or read the manual.:rolleyes:
  7. Replies
    11
    Views
    1,025

    Re: C253 Operational Question

    Sounds like the options aren't configured properly in the PCL driver. You might want to check in properties window of the driver, go to configure tab and see if the duplex and correct finisher are...
  8. Re: bizhub C250 Keeps asking to remove and reinstall drum

    Thanks, Darryl
  9. Re: bizhub C250 Keeps asking to remove and reinstall drum

    Update: :cool:Changed the front wire harness under the inner cover. All is Good!
  10. bizhub C250 Keeps asking to remove and reinstall drum

    Hey Guys,

    I have a bizhub C250 that keeps asking to remove and reinstall drums. Black Drum only used 20% of expect life. MFP just over 65k on meter. It was also having trouble with the side door...
  11. [CQ] Re: Bizhub 421 - Streaks in subscan direction

    update; Changed the Drum Blade and refit side seals and that seemed to have gotten rid of 98% random streaking. It didn't completely remove all marks as I'll get a hint of a faded stripe in say 1 out...
  12. [CQ] Re: Bizhub 421 - Streaks in subscan direction

    missing sample2823028231
  13. [CQ] Bizhub 421 - Streaks in subscan direction

    Hey Gang,

    I have a Bizhub 421 streaking in subscan direction. I have taken out and cleaned drum, blade and charge grid, vacuumed out toner waste well and re-assembled. Also scrubbed corona wires...
  14. Replies
    5
    Views
    418

    Re: Line in Subscan Dir Canon 5570

    Thank you Zoraldinho for the fast reply and for the instruction and Tech Bulletin. It will be a Big help in fixing the issue. I', heading back Tomorrow so I'll report back after I have a chance to...
  15. Replies
    5
    Views
    418

    Re: Line in Subscan Dir Canon 5570

    Thank you, Canuck for the fast response. Did not see any issue with upper fuser and cleaning web was less than halfway through. I'm going back Tomorrow so I'll have a better look at the drum area....
  16. Replies
    5
    Views
    418

    Re: Line in Subscan Dir Canon 5570

    p print sample28226
  17. Replies
    5
    Views
    418

    Line in Subscan Dir Canon 5570

    Hey Gang,

    Haven't worked on this model before. Getting a line in the subscan direction on a Canon iR5570. I have run wire cleaning in both user and service mode and can get rid of line...
  18. Replies
    14
    Views
    1,071

    [Misc] Re: Canon ir3225 black lines

    As Zoraldinho said..........:rolleyes:
  19. Replies
    6
    Views
    1,488

    Re: lines in sub-scan direction on C3380

    Great call on this Copier Tech. I had replaced ITB cleaner with no improvement, so I tore apart the drum and found the drum blade caked with toner. Cleaned drum blade & primary transfer roller, wiped...
  20. Replies
    6
    Views
    1,488

    Re: lines in sub-scan direction on C3380

    Thanks again, Teckat. I'll try that lubricant.
  21. Replies
    6
    Views
    1,488

    Re: lines in sub-scan direction on C3380

    Thanks Teckat. Is it chatter from the blade or needs to be coated with drum powder? Do these blades flip? I wiped it down twice w/ alcohol wipe and vacuumed out the feed screw tube. Thought that...
  22. Replies
    6
    Views
    1,488

    lines in sub-scan direction on C3380

    Hi guys,

    I had a call on a c3380i for light prints for black only originally. all colors looked fine. Checked and found it was happening in different apps and also on internal prints so I cleaned...
  23. Thread: dc432

    by Victor285
    Replies
    9
    Views
    670

    [Jamming] Re: dc432

    Ran the Fault History and got Codes E4-1 Face Up exit switch code and an E8-1 Duplex Paper Sensor. Mostly E4-1. Followed RAP procedures and both switches checked out fine, Checked Duplex Inverter...
  24. Thread: dc432

    by Victor285
    Replies
    9
    Views
    670

    [Jamming] Re: dc432

    Thanks for the response Frenci, I'm heading there Monday, I'll get back to you then.
  25. Thread: dc432

    by Victor285
    Replies
    9
    Views
    670

    [Jamming] Re: dc432

    Thanks Adrianstro for the quick response. Do I take off the metal arms as well or will I need the contact for continuity? I'm heading there Monday, I'll get back to you with the error code then.
Results 1 to 25 of 61
Page 1 of 3 1 2 3