Search:

Type: Posts; User: scanmc

Page 1 of 4 1 2 3 4

Search: Search took 0.13 seconds.

  1. Replies
    9
    Views
    726

    [CQ] Re: OKI B721 Blank prints?

    No it doesn't throw an error code. That Led head is very easy to knock out of place as its kept in place by two springs. People have a tendency to slam the the lid and if that LED head isn't lined up...
  2. Replies
    9
    Views
    726

    [CQ] Re: OKI B721 Blank prints?

    Make sure the LED head is not out of place. I've seen more than once where the customer has knocked it up so its not pointing at the the drum unit while pulling out the drum & toner unit
  3. Replies
    4
    Views
    5,084

    Re: MFX-3530 Toner low

    I'll check when I get back in the office
  4. Replies
    4
    Views
    5,084

    Re: MFX-3530 Toner low

    I just sent you a PM
  5. Replies
    10
    Views
    2,518

    Re: MJ-1101 finisher

    I decided to give it the old college try one more time not to mention my stubbornness. After removing the covers to be able to get the elevator sensors such as BC and MC recommended low and behold...
  6. Replies
    10
    Views
    2,518

    Re: MJ-1101 finisher

    Thanks for all the replies. Yep not my first rodeo on the donated machine issue. Like most of you said I'm just going to remove the finisher and call it a day.
  7. Replies
    10
    Views
    2,518

    Re: MJ-1101 finisher

    BC ----No error message. Machine is a estudio 3530C I can manually move the sort tray to the up position---select sort--- hit the start button and the tray will head south all the way to the bottom...
  8. Replies
    10
    Views
    2,518

    MJ-1101 finisher

    I normally don't work on Toshiba machines but the local church was donated one of these to them and ask me to take a look at it. The problem is the sort tray on the finisher goes straight to the...
  9. Re: Can Konica supplies be made to fit in a Muratec?

    We just buy all Muratec K drums for that series machines then replace them with a color chip purchased from one of the aftermarket suppliers if your going to use them in the CMY slots. The drums are...
  10. Re: Can Konica supplies be made to fit in a Muratec?

    I've done the end cap switch on the toners in a pinch with the Konica brand. This series toner cartridge is not chipped. As far as drums are concerned we have always just purchased the K Muratec...
  11. Replies
    4
    Views
    826

    [Misc] Re: Konica C258 Color drum conversion

    Bummer. Yep that's what I thought was going on.

    Thanks for the input.
  12. Replies
    4
    Views
    826

    [Misc] Konica C258 Color drum conversion

    Yesterday I tried to convert a C258 K drum unit into a color unit via the drum reset chip and removing the small plastic plastic piece that stops the unit from sliding in all the way in the color...
  13. Replies
    5
    Views
    998

    [CQ] Re: Oki c9655 colour misregistration

    I learned my lesson years ago to only use OKI supplies. I woulds say if it happened after the user installed the non OKI drum units that's your culprit
  14. Replies
    0
    Views
    362

    [Wanted] CS1635 Doc Feed Harness

    Does anyone have one of these beauties laying around on the shelf?
  15. Replies
    2
    Views
    2,075

    Re: Muratec MFX-3535 Turns on/off

    Did you try a new power supply?
  16. Replies
    4
    Views
    1,024

    Re: Looking for OKI Tech in Chicago Area

    Dealer Locator | OKI Data Americas
  17. Replies
    4
    Views
    599

    Re: CS-221 Developer / DV Unit ????

    One more thing, Also make sure the mirrors are clean especially if the copies are light down the center. The fuser has a tendency to leave a hazy film on the mirrors since it sits right bellow them....
  18. Replies
    4
    Views
    599

    Re: CS-221 Developer / DV Unit ????

    I know on the old CS2030 the developer was changed out of the dv unit.If I recall on the CS 2050 -2550 series these machines were a mono component machine where the toner\dv was all in one. On these...
  19. Thread: MPC5502

    by scanmc
    Replies
    2
    Views
    357

    [Misc] Re: MPC5502

    Thanks! Found it
  20. Thread: MPC5502

    by scanmc
    Replies
    2
    Views
    357

    [Misc] MPC5502

    Good afternoon. I'm looking for the part number for the top half of the case that the transfer roller sits in. This customer seems to have gotten aggressive and slammed the door shut breaking the...
  21. Re: Oki MC860 optional paper tray parts catalog required

    I checked on the OKI website and I don't see any parts list for the optional tray. I do have a parts machine in the back but by looking at your location that might be an issue getting it to you.
  22. Replies
    0
    Views
    389

    [For Sale] Muratec MFXC2828 OEM Supplies

    Make an offer

    2-Black toners
    1-Magenta toner
    1-Cyan toner
    1-Yellow toner
    1-Waste container
    1-Cyan dv unit
  23. Thread: Ricoh MPC5501

    by scanmc
    Replies
    8
    Views
    605

    [Jamming] Re: Ricoh MPC5501

    Well It ended up being the gate shaft and bushings were so gummed up that the solenoid would open or close properly. After a good cleaning she's working like a champ again. You would thing after all...
  24. Thread: Ricoh MPC5501

    by scanmc
    Replies
    8
    Views
    605

    [Jamming] Re: Ricoh MPC5501

    Thanks for the info. Heading back out here today for a closer look.
  25. Thread: Ricoh MPC5501

    by scanmc
    Replies
    8
    Views
    605

    [Jamming] Ricoh MPC5501

    I don't do a lot of work on Ricoh's but I've got this one out in the field. My issue is when duplexing the machine gets about an inch out of the fuser when entering the bridge then jams (J024 code) I...
Results 1 to 25 of 94
Page 1 of 4 1 2 3 4