Search:

Type: Posts; User: Bix

Page 1 of 20 1 2 3 4

Search: Search took 0.10 seconds.

  1. Replies
    20
    Views
    1,445

    Re: We comment on iSeries firmware

    For now, I haven't had this problem. But this certainly scares.
    I believe that at this point, perhaps it is best not to update until you have problems. This is quite frustrating because I don't...
  2. Replies
    20
    Views
    1,445

    Re: We comment on iSeries firmware

    Hi, I inform you that the G00-B6 firmware is out in all iSeries models in Europe.
  3. Replies
    4
    Views
    168

    Re: printing delay on Konica c308

    Have you tried to verify DNS and Gateway?
    There may be multiple dns/gateways in your case
  4. Replies
    21
    Views
    2,305

    Re: Some MFPs stop communicating with the CSRC

    The absurd thing is that in some cases it works for me even with those two flags disabled and then stop working at any moment.
    So do it! Disable those flags like my colleague tbservice says! :)
  5. Replies
    15
    Views
    449

    Re: 458e shuts down during job

    In other cases it was the faulty power strip (in the manual it is forbidden to connect to these devices but 50% of customers ignore this rule). It did not support printer loading.
  6. Replies
    15
    Views
    449

    Re: 458e shuts down during job

    Are you sure the problem is the printers? I have had several customers with UPS. The ups was not powerful enough and caused the printer to shut down as soon as someone launched a job.
  7. Replies
    4
    Views
    325

    Re: Word of warning i series

    Thanks for the warning!
    I currently have FS533 internal finishers installed and they seem to have no problems with the firmware update
  8. Replies
    21
    Views
    2,305

    Re: Some MFPs stop communicating with the CSRC

    Yes, you have to activate it.
    It also disables WebDAV
  9. Replies
    3
    Views
    208

    [Misc] Re: New KM firmware for i series

    Hey, don't be like my colleagues. When they report a failure and I ask: "What firmware do you have installed?" and they answer me "The last one", I go crazy and I get angry. :mad::mad::mad:Because...
  10. Replies
    25
    Views
    3,149

    Re: bizhub c3300i/c4000i IU problems

    I do not think it will be mentioned in a bulletin otherwise it would start the valaganza of requests for the guarantee
  11. Thread: PS5 Sold out

    by Bix
    Replies
    0
    Views
    88

    PS5 Sold out

    Hey guys,

    What do you think about Play Station 5? Soldout in 1 minute!
  12. Replies
    4
    Views
    261

    Re: C284 whistles in standby

    It's funny that a noise filter causes noise. is an oxymoron
  13. Replies
    30
    Views
    1,546

    [Dead] Re: C250i does not boot...

    Okay, but the result is not clear to me. What accesses with the new Storage Board? I have solved, for now, always with a new Storage Board. Be careful, it also takes 10-15 minutes when you install...
  14. Replies
    0
    Views
    119

    Workplace Hub Pro is now in iSeries

    Hi, I saw the launch of Workplace Hub Pro. In reality I have never touched the Workplace but it is an interesting project.
    Printing is shrinking and the IT world is evolving in businesses. This...
  15. Replies
    30
    Views
    1,546

    [Dead] Re: C250i does not boot...

    I think I read "you have renewed the storage board". So I guess you didn't replace but you just formatted, is that correct?


    Maybe the file system is damaged so even if you try to format it...
  16. Replies
    30
    Views
    1,546

    [Dead] Re: C250i does not boot...

    Hi, have you tried the G00-B5 firmware? This solves several problems.
    Disconnect ADF (including dual scan card) temporarily during update if it gives you NG again.


    I ask you to restore original...
  17. Replies
    8
    Views
    232

    [Misc] Re: B4052 / b4752 replace imaging unit message

    My bizhub 4052 imaging units often last 70% of their expected life. Rare units have lasted over 100%. Allan sure the printer stops? For now, I haven't had anyone stop by. The only problem was the...
  18. Replies
    9
    Views
    382

    Re: Konica 654e and SMB1.0

    This is true. I am one who often changes in new technologies. But my customer are not of the same opinion. The more the price is reduced, the more the product is of quality. Sometimes, in order to...
  19. Replies
    9
    Views
    382

    Re: Konica 654e and SMB1.0

    Does Series 4 also have SMB3.0?
    Or just 4e?
  20. Replies
    18
    Views
    641

    Re: C3350i and light blue stripes

    As expected, these are the lines of shame. To delete them it was enough just to follow the installation manual
  21. Replies
    12
    Views
    539

    [Misc] Re: bizhub c300i "the original size was detected"

    Guys, before disassembling try this. I had this problem on 2 bizhub C250i. At 90% it is because the ADF is pushed too hard against the glass. Adjust the height screw and you will 90% solve this...
  22. Replies
    2
    Views
    146

    Re: Bizhub 4750 stuck on logo

    Sometimes it is enough to keep the network cable disconnected
  23. Replies
    2
    Views
    163

    Re: C-368, C-3201 code...(fuser)

    If you can help, there is a load check to check the status of the M3 engine.
    Check code: 45
    Multi code: 1, 2, 3, 4, 5
  24. Re: C3300i/C4000i/C3320i/C3350i/C4050i Fan (FM3) issue

    Yes, I am aware of this. But I think this is strange. Usually it doesn't. When this happens it's because the printer freezes (goes offline, unknown jams, etc.)
  25. Re: C3300i/C4000i/C3320i/C3350i/C4050i Fan (FM3) issue

    I confirm that I have had this problem. But with the printer turned off! Yes, you got it right. I turned off the main switch and the fan continues to run for 5-10 minutes. I usually resolve by...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4