Search:

Type: Posts; User: copyman

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    22
    Views
    605

    Re: Biz C224e - Muratec version?

    I had a parts C224 and used the toner cover from that.
  2. Replies
    4
    Views
    182

    [Error Code] Re: don't boot up error

    I realize in other countries this may be only old models you can get or afford so I will take a different approach then the other techs even though they have good points.

    Even with Firmware update...
  3. Replies
    22
    Views
    605

    Re: Biz C224e - Muratec version?

    It's actually a soft switch that "badges" the copier. I think they come out of the same factory with a different serial # label, soft switch changed & boot screen. And as was discussed in this thread...
  4. Replies
    8
    Views
    333

    Re: Konica C220 print quality problem

    Like other poster mentioned replace black drum as well or you will be back there when the developer dumps again from over life drum shorting out.

    A lot of posts on this forum about "4 series...
  5. Replies
    22
    Views
    605

    Re: Biz C224e - Muratec version?

    Figured that's what you meant. I should of been more clear just didn't want to have to cut ribs on 10 or 20 toners at a time. If it was at regular customer getting one two toners a year no big deal...
  6. Replies
    22
    Views
    605

    Re: Biz C224e - Muratec version?

    Just wanted to update. The Muratec version can totally be converted to the BizHub model. I swapped out the toner holder & front cover from a parts C224e. Updated firmware and changed Dip switch. The...
  7. Replies
    22
    Views
    605

    Re: Biz C224e - Muratec version?

    can't ask the customer the cut the fin. it took a little more time but as I mentioned I used the toner holder from a C224. Swapped front cover to a C224e. Firmware & dip switch change worked and...
  8. Replies
    1
    Views
    105

    Re: Konica Minolta Bizhub C364 Firmware

    Is it for C364 or C364"E"? PM me your email and will send it.
  9. Replies
    22
    Views
    605

    Re: Biz C224e - Muratec version?

    Thanks!
  10. Replies
    22
    Views
    605

    Re: Biz C224e - Muratec version?

    Ok, so I swapped out the toner holder so the Muratec will now accept K/M toners. It's going to a customer with 5 other C224e's and wants to use all Kon/MinTN321 toners.

    Few other questions:
    ...
  11. Re: Bizhub C3350 vertical lines in the center of the printed page

    When I've had those lines from the transfer belt many time I was able to replace just the trans belt cleaning blade (aftermarket) instead of expensive transfer belt. Especially when trans belt is no...
  12. Replies
    14
    Views
    1,703

    Re: C3350 vs c3351 fuser?

    Another yes vote for me. Done it several times no issues. Only difference I see is color of lock latches, new are black, old blue.
  13. Replies
    22
    Views
    605

    Re: Biz C224e - Muratec version?

    Had a chance to look at a C224 toner assembly from parts machine, looks like after removing complete toner hopper assembly there are 2 screws to take toner holder off of top. This is piece that has...
  14. Replies
    22
    Views
    605

    Re: Biz C224e - Muratec version?

    Thanks for the replies.

    I have a C224 parts machine I may just swap out the toner cover so the C224 toners will fit without cutting anything. And put a label on machine near toners saying to use...
  15. Re: Bizhub C3350 vertical lines in the center of the printed page

    Looks like black image unit or transfer belt need to be replaced. What do the consumable life counters look like?
  16. [Misc] Re: bizhub 458e - one strange scanning issue - low resolution scans no matter what

    What does quality look like if you scan off the glass not using the ADF?

    Did you remove the glass and clean the optics & lens?
  17. Replies
    4
    Views
    160

    [Error Code] Re: Error code C-D012 on KONICA C754e

    Format HDD and if that don't work replace it.

    You can still get into service mode to format HDD even with the trouble code on display, just have to wait a few minutes.
  18. Replies
    25
    Views
    1,128

    Re: Biz C224e misfeed

    I agree it's ok not to agree:)
    Will keep in mind if way I've been doing it ever doesn't work. Options are always good to have.

    Only thing techs can do on this forum is post what works for them....
  19. Replies
    22
    Views
    605

    Biz C224e - Muratec version?

    Can the MFX C2280 Muratec be changed to take Konica Minolta C224e toner? With changing firmware, board, etc ??? I just need it to accept genuine Kon-Min toner & other consumables.

    Thanks in advance
  20. Replies
    25
    Views
    1,128

    Re: Biz C224e misfeed

    Sanding along the shaft was what they teach at Konica Minolta factory training school. Appreciate the advice but have to keep doing what has been working for me. Been doing it for many years and...
  21. Replies
    3
    Views
    102

    Re: Oki C531 printer

    Thanks for the reply.

    Not trivial I thought same thing.

    They actually replaced the drum unit assembly and when they closed top cover message appeared. When I got there and they explained how it...
  22. Replies
    25
    Views
    1,128

    Re: Biz C224e misfeed

    Just my preference, emery cloth works best out of everything I've tried.

    What ever is used the most important thing is to "sand" in direction of shaft length not "around" the shaft. You want to...
  23. Replies
    3
    Views
    102

    Oki C531 printer

    Hi,

    Probably only one that can help me with this is someone who knows Oki and had the same exact issue.

    Don't know Oki that well but a good customer asked me to take a look while there...
  24. Replies
    13
    Views
    5,303

    Re: Bizhub C253 Transfer Belt Help

    Are you sure you put the right fuse in "80mA"? If you put wrong fuse in it may have damaged the reset circuity. At this point only option is to update the firmware and try to turn off messages. Not...
  25. Replies
    25
    Views
    1,128

    Re: Biz C224e misfeed

    Thanks everyone for the input. Turns out it was the Sep roller torque limiter. After confirming it was that I removed the PF unit and replaced one way's after scuffing up shafts. Already had the new...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4