Search:

Type: Posts; User: spanky

Page 1 of 16 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    5
    Views
    164

    Re: MX5070V with LC17N

    Have you checked your height adjustment on the LCC? Was the mylar guide installed properly on the engine where the paper enters? If all of this is correct I would try the clutch or the sensor.
  2. Replies
    4
    Views
    247

    [Error Code] Re: F2-41 error on Sharp MX-3640N

    I have never seed a Sharp copier tell you to change the developing unit. Are you sure it is not saying to install the developing unit? This could be caused by a bad connection of the connecter on...
  3. Thread: MX-M364N F2-78

    by spanky
    Replies
    6
    Views
    256

    [Error Code] Re: MX-M364N F2-78

    Clean the connection between the right side door and the engine.

    If this does not work then I suggest replacing the transfer roller unit.
  4. Replies
    10
    Views
    298

    Re: Network Scanner Tool Lite

    This tool should have put the information for this scanning in the address book of the copier.

    Look under FTP scanning and then check the address book for the path to the folder.
  5. Replies
    10
    Views
    298

    Re: Network Scanner Tool Lite

    The network scanner lite tool used FTP scanning, not SMB.
  6. [CQ] Re: Sharp MX-M3571 ADF second side has gray background and garbled

    do you have a power filter on the copier's AC connection?

    I had an MX-5140 act the same way and it was electrical noise.

    Put a filter on it and never had another issue.
  7. Replies
    10
    Views
    375

    [Electrical] Re: Ar 6020 scanner and printer disconnected

    If you check his profile, the last copier he was trained on is over 30years old.
  8. Replies
    1
    Views
    568

    [CQ] Re: MX-3070/MX-3071 fuser cleaning page

    System settings/ Image quality adjustment/ collective adjustment
  9. Replies
    7
    Views
    325

    Re: PN-L651H Aquos Board

    Have you removed the power supply board to check for a part number on it?
  10. Re: MX-3640N Not able to scan large files to email or USB

    Go into the system settings/scan settings.

    You can set the maximum size for email and other scans there.

    Be sure it is not set to a lower number than needed based on any limitations in the...
  11. Replies
    3
    Views
    402

    [CQ] Re: MX2640 missing image areas

    If you have removed the PTC before this happened, be sure it is installed properly.

    It can be installed so a part of it is elevated and rubs the toner off the page.
  12. Replies
    10
    Views
    1,224

    [Error Code] Re: Sharp AR-M550u Error F2 only

    On most Sharps if you have an F2 only and the machine still operates you have an issue with the temperature or humidity sensor.

    Most Sharps have these located in the right side door, not sure...
  13. Thread: sharp-mx2300n

    by spanky
    Replies
    1
    Views
    220

    Re: sharp-mx2300n

    Through the web page go into the users setup and disable users.
  14. Thread: Venting...

    by spanky
    Replies
    42
    Views
    8,457

    Re: Venting...

    I am 65 and don't know how much longer I can tolerate the customers who think they know more than me.

    I started in this business in 1986 and still haven't learned my lesson.

    Too late to try...
  15. Re: Sharp MX-6070v machine unable to print and photocopy

    You need a Sharp tech to contact Sharp with the serial number of your machine so Sharp can issue a password reset for your machine.

    Then you can follow the steps to disable the OSA function of the...
  16. Re: MX-8090N 11x17 Image Prints offset 2mm on Long Edge

    50-10
  17. Re: Sharp MX-6070v machine unable to print and photocopy

    You need to get into the external accounting settings and disable it.
  18. Replies
    12
    Views
    736

    Re: Printer MX-4111 not turning on

    Have you had control box2 out of the machine?

    I have found this can happen if it has been removed and upon installing it the contacts don't line up properly.

    I have had to remove and reinstall...
  19. Replies
    2
    Views
    260

    Re: MX-M7570 toner in tray 2

    If it is in the rear of the tray I would suggest it could have something to do with the toner waste system
  20. Re: How to calibrate drums of Sharp machines (MX-2640N)

    Go into the settings mode, choose the security settings, choose Initialize private data.

    This will take some time to run but all data in address book, document filing, etc will be removed.
  21. Thread: MXB201

    by spanky
    Replies
    4
    Views
    301

    Re: MXB201

    You can't print it out, sim 22-5 will display it.
  22. Thread: MX2640 U1-01

    by spanky
    Replies
    2
    Views
    409

    [Error Code] Re: MX2640 U1-01

    Battery (CR2032_PA)

    Sharp part # UBATL0021FCPZ

    I don't know if it will recharge
  23. Replies
    9
    Views
    787

    Re: MX3060 extended lan

    See sim 26-33 in the MX-6071 service manual
  24. Re: What is the dumbist customer comment/question you've heard?

    I had a customer copy from a color original to make a black and white copy.

    She later complained she had put the black and white copy in the document feeder and asked for a color copy and it came...
  25. Replies
    10
    Views
    743

    Re: Sharp MX-C301W Is it a reliable table top?

    The MX-C301W has been replaced with the MX-303W and MX-304W.

    You can no longer order the MX-301W.
Results 1 to 25 of 400
Page 1 of 16 1 2 3 4