Search:

Type: Posts; User: Utahrob1

Page 1 of 2 1 2

Search: Search took 0.06 seconds.

  1. Replies
    4
    Views
    3,546

    [Error Code] Re: Latch the developer unit ES 355

    Tnx for the reply. I have re-seated all the connectors several times. I also tried a different imaging unit.
  2. Replies
    4
    Views
    3,546

    [Error Code] Latch the developer unit ES 355

    Hello all

    I did a drum and developer change on a ES 355. When I put everything back in the machine and turned it on, the machine says to "latch the developer unit"'
    I took the process unit back...
  3. Replies
    14
    Views
    7,176

    [Misc] Re: Firmware update on a Sharp MX 4101n

    Thanks all for the help. Everything is loaded fine.
  4. Replies
    16
    Views
    1,320

    Re: IRA8105 smear or dropping toner.

    Did this just start happening? Or was it happening before the new DV unit? I have had this happen twice before and it was a bad DV unit. Good luck!
  5. Re: IR3045 Print Offset to 4cm to the right NEED HELP BADLY.

    Yes replace clutch. Also make sure the reg sensor is not sticking.
  6. Replies
    14
    Views
    7,176

    [Misc] Re: Firmware update on a Sharp MX 4101n

    I dont have access to the Sharp site to get the watermark firmware. Is is emailable? or can someone send me a dropbox link? my email is robert8175@gmail
    Thank you!!
  7. Replies
    14
    Views
    7,176

    [Misc] Re: Firmware update on a Sharp MX 4101n

    Ok i just read that i need to rename file to emupdate_12.sfu. I will try that to see if it helps.
  8. Replies
    14
    Views
    7,176

    [Misc] Re: Firmware update on a Sharp MX 4101n

    Tnx all. I have the firmware loaded on both machines. You rock!!! One problem though both machines are giving me a U2-60 error. Something to do with the watermark portion of the firmware I am...
  9. Replies
    14
    Views
    7,176

    [Misc] Re: Firmware update on a Sharp MX 4101n

    you cant get into sim?
    Hey thanks so much for the quick reply. Is there a way of doing this if
  10. Replies
    14
    Views
    7,176

    [Misc] Firmware update on a Sharp MX 4101n

    Good morning all

    I need to know how to install the firmware from a flash drive. Any help would be awesome!!

    Tnx, Robert
  11. Replies
    5
    Views
    1,034

    The problem is the laser safety switch at the...

    The problem is the laser safety switch at the front door interlock area.
  12. Replies
    10
    Views
    2,302

    Panasonic does use true Postscript. But you are...

    Panasonic does use true Postscript. But you are correct that PCL is emulated.
    Setting them up for standard GDI printing will make them print faster.
  13. Replies
    3
    Views
    1,418

    The manuals are not electronically posted. What...

    The manuals are not electronically posted. What do you need specifically?
  14. Replies
    4
    Views
    1,241

    They all are pretty good machines. Like all other...

    They all are pretty good machines. Like all other brands they have some weak areas, but all in all there pretty reliable. A lot of the calls are just toner or drum calls. Samsung as a manufacture is...
  15. Replies
    9
    Views
    1,038

    DO NOT use this paper trick on this machine. The...

    DO NOT use this paper trick on this machine. The doctor blade gap should never be messed with on any machine. If you are messing with the gap you are putting a band aid on the real problem...
  16. Thread: skewing

    by Utahrob1
    Replies
    5
    Views
    665

    No it wouldn't. It is all about timing from the...

    No it wouldn't. It is all about timing from the first tray for some reason. Go Raiders ;-)
  17. Thread: DP-7000

    by Utahrob1
    Replies
    3
    Views
    514

    SAFETY THERMISTOR OVER HEAT FAIL Description...

    SAFETY THERMISTOR OVER HEAT FAIL
    Description
    SAFETY THERMISTOR has detected 227
    Degrees Celsius or higher (Monitor value: 164) 5 times
    in a row.
    To clear this fault, open FRONT COVER, change...
  18. Replies
    3
    Views
    644

    The front switch is a soft power down. If you...

    The front switch is a soft power down. If you have checked the switch itself and it is good it may be a really old version of firmware. The old firmware is not recognizing the interrupt or does not...
  19. Thread: Windows 7

    by Utahrob1
    Replies
    2
    Views
    447

    Vista driver is suppose to be compatible. I have...

    Vista driver is suppose to be compatible. I have not run into one yet though.
  20. Thread: skewing

    by Utahrob1
    Replies
    5
    Views
    665

    Under F6 service mode you can adjust the loop...

    Under F6 service mode you can adjust the loop adjustment for the first tray. It could be a middle roller clutch as well.

    Good luck, Rob
  21. Replies
    2
    Views
    1,084

    Yes that is right, usually a garbage can. You...

    Yes that is right, usually a garbage can. You just need to lift the trays up so they are even again and then cycle the power.
  22. Thread: 6030

    by Utahrob1
    Replies
    2
    Views
    515

    Door exit sensor is stuck.

    Door exit sensor is stuck.
  23. Replies
    3
    Views
    935

    Sounds like you may need to do a shipment set. ...

    Sounds like you may need to do a shipment set.

    Good luck Robert
  24. Replies
    6
    Views
    1,310

    Anytime, glad it worked.

    Anytime, glad it worked.
  25. Replies
    8
    Views
    889

    They did resolve it with mylars that would clean...

    They did resolve it with mylars that would clean the auger. Or knock the toner off the auger that is, so the toner wont build up on the auger. I have no idea if they still sell that mylar or even...
Results 1 to 25 of 38
Page 1 of 2 1 2