Search:

Type: Posts; User: Santander

Page 1 of 20 1 2 3 4

Search: Search took 0.57 seconds.

  1. Replies
    3
    Views
    52

    Re: Newbie introduction

    Welcome Aboard!
  2. Thread: Hi everyone!

    by Santander
    Replies
    7
    Views
    212

    Re: Hi everyone!

    Welcome Aboard!
  3. Replies
    15
    Views
    879

    Re: Kyocera 7002i thick solid black line

    If you look at the sample you provided, the black stripe has a margin, it does not go to the edge of the page. That tells me this is a scan issue and not a print engine problem. If it was a print...
  4. Replies
    8
    Views
    277

    Re: Newbie to the forum.

    Welcome Aboard!
  5. Replies
    6
    Views
    193

    Re: Hello everyone

    Welcome Aboard!
  6. Thread: Hello

    by Santander
    Replies
    8
    Views
    307

    Re: Hello

    Welcome Aboard!
  7. Thread: Hello!

    by Santander
    Replies
    11
    Views
    495

    Re: Hello!

    Welcome!
  8. Re: rotate offset when selecting multiple sets

    It appears that you or the user has set rotate offset for multiple sets [no finisher] but the cassettes are set to a specific size or are not set to auto. How are the cassettes loaded? Both letter...
  9. Replies
    8
    Views
    266

    Re: Newbie Checking In!😊

    Welcome Aboard!
  10. Replies
    1
    Views
    177

    [Jamming] Re: M2540 J41x,J42x jams fix

    Thanks for your assessment and a possible resolution to the problem, but why go through all that when Kyo will replace the fuser under warranty with no questions asked.
  11. Re: Ricoh copier email transmission fail with Go Daddy

    Your assessment is correct. Don't forget that smtpout.secureserver.net also utilizes port 3535, which they do not block. Since using the 3535 port we have not had any issues.
  12. Replies
    5
    Views
    451

    Re: taskalfa 2550ci network

    You said that the embedded network connection and the optional IB51 are both not working, I would suspect that the switch/router the machine is connected to has a bad port. Can you use another...
  13. Replies
    8
    Views
    476

    Re: Newbie "working" from home

    Welcome Aboard. Nice intro, you may be able help sooner than you think!
  14. Replies
    20
    Views
    1,063

    Re: DATA SECURITY KIT E

    The Data Security Kit protects the HDD(s) and should not have anything to do with your problem. I am assuming you tried scanning one page from the glass and updated the firmware. Since you cannot...
  15. Replies
    7
    Views
    313

    Re: Newbie checking in!

    Welcome!
  16. Thread: Hello All

    by Santander
    Replies
    7
    Views
    383

    Re: Hello All

    Welcome Aboard!
  17. Re: Kyocera Taskalfa 8353 operation panel locking up

    When you say lock up? Do you mean that touching an item on screen nothing happens? Have you run U201 to initialize the touch panel? It could be nothing more than the unit is seeing where you touch...
  18. Replies
    6
    Views
    675

    Re: olivetti 4500i error 0000

    A jam 0000 indicates the machine see's a jam on power up. It could be anything from the feed sensors in the default tray to the registration sensor to the exit sensor. Had one of these units a...
  19. Replies
    11
    Views
    1,226

    Re: Kyocera "bulletins"

    What happened to the days when Kyocera would push out email notifications of new Tech Service Bulletins? Now even if you log on to the website and go to downloads and select technical-bulletins it...
  20. Replies
    12
    Views
    2,513

    Re: FS-C8525MFP asking for Maintenance Kit A

    Agree with Blackcat to check the cleaning of the transfer belt. This unit also has had the bad cleaning pipe for the transfer belt which backs up the cleaned toner in the cleaning brush and then...
  21. Replies
    5
    Views
    2,341

    Re: wierd problem TA3501ci

    Your first code of C6950 points to the fuser IH PWB [it could also be caused by the fuser]. After you replaced the LV PWB, did you check U169 to make sure it is set to the voltage for your country? ...
  22. Replies
    1
    Views
    619

    Re: CopyStar 4551 Default to B & W

    Go into the preferences settings on the print driver, change to black & white and save.
  23. Replies
    5
    Views
    1,027

    Re: Kyocera KM-2560 - jamming

    Have seen this a number of times. The exit assembly when it pulls the paper back in for printing/copying on the backside skews the paper and causing the jam you showed. You could try pulling the...
  24. Replies
    16
    Views
    2,380

    [Jamming] Re: TA-6501i with a Mailbox Tower MT-730

    I disagree that the document with large black borders was causing the mailbox jam. Once the image is printed with large black areas and does not cause a jam in the machine itself and it processes to...
  25. Replies
    12
    Views
    1,910

    Re: New Taskalfa scan smaller when viewd

    Have you tried printing as an image instead of using the Acrobat generted file? If you can print the file as an image and it prints OK, then the problem is not machine based but in the program used...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4