Search:

Type: Posts; User: acribari

Page 1 of 2 1 2

Search: Search took 0.13 seconds.

  1. Replies
    19
    Views
    1,475

    Re: Sharp MX-M904 Image Shift

    Ah, that makes sense. I did not have any formal training on this model. Just have the service documentation. Thanks for all the help.

    ;)
  2. Replies
    19
    Views
    1,475

    Re: Sharp MX-M904 Image Shift

    Thank you very much for the info. I went to the account today and ran 50-10 on HCT Bypass tray and the data setting was on 48. I had to move it to 95 and now its perfectly centered on 12 X 18 and...
  3. Replies
    19
    Views
    1,475

    Re: Sharp MX-M904 Image Shift

    No I have not tried sim 50-10. The high cap trays are centered so will this mess them up if I use sim 50 -10?

    I can go back and give it a try.

    They are running 80 pound card 12X18 and it...
  4. Replies
    19
    Views
    1,475

    Re: Sharp MX-M904 Image Shift

    Does anybody have an answer for this issue?

    I need to center the image on 12 X 18 and all other paper sizes from the multi bypass tray. The bypass is Model MX-MF11 and sits on top of the high...
  5. Replies
    19
    Views
    1,475

    Re: Sharp MX-M904 Image Shift

    Ok I will give it a try.

    I posted at the same time you did. Make sure we are talking about the same bypass model.

    Thanks
  6. Replies
    19
    Views
    1,475

    Re: Sharp MX-M904 Image Shift

    All sizes. It does recognize 12 X 18 is loaded. I ran sim 40-2 but not sure if I did the correct sim. I have bypass tray Model MX-MF11. it sits on top of the high cap trays 5 and 6. Just wanted...
  7. Replies
    19
    Views
    1,475

    Re: Sharp MX-M904 Image Shift

    ok, so all the trays are feeding with the paper centered. The bypass tray is the problem. I can't seem to center the image. the bottom of the image is too close to the bottom of the sheet on 12 X...
  8. Replies
    19
    Views
    1,475

    Re: Sharp MX-M904 Image Shift

    How do you acquire a template for the media ?

    I'm not sure how to do this. I am new on this machine model.

    I am actually going over there now to see what I can do.

    Any info. would be great....
  9. Replies
    19
    Views
    1,475

    Re: Sharp MX-M904 Image Shift

    I will be going over there on Friday. I will get back to you with more details. Basically they have a pre perforated sheet of about 20 tickets or so ( I will look at the sheet to make sure again)...
  10. Replies
    19
    Views
    1,475

    Sharp MX-M904 Image Shift

    Hello again,

    I have a customer that is trying to run perforated tickets on pre perforated paper. The image does not line up in the center of the perforated marks. They can shift it but then it...
  11. Replies
    24
    Views
    2,222

    Re: Sharp MX-M904 Still Good?

    I figured it out. One of the exit rollers was not snapped in all the way and it prevented the height sensor from not actuating. After snapping the white roller clip (oval shaped) back on the...
  12. Replies
    24
    Views
    2,222

    Re: Sharp MX-M904 Still Good?

    Grrrrrrr. I have another issue with the finisher. FN-22 finisher. the exit lift errors out. F0-03. Any clues.

    I tried a sensor and it still just stutters when it initializes and gives the...
  13. Replies
    24
    Views
    2,222

    Re: Sharp MX-M904 Still Good?

    Great!!! Thank you both for the replies. I will try this next call.

    Thanks again.
  14. Replies
    24
    Views
    2,222

    Re: Sharp MX-M904 Still Good?

    Ok, I finally got the machine all installed and it has been running good. I had some issues with the finisher but I got that resolved.

    Now, I need to use the Raw copy tool and an SD card to...
  15. Re: MX-M904 Finisher Jams in the Saddle Fold entrance area.

    Instead of fiddling around with the finisher, since it is a new install for the customer, I got another finisher with the same options. FN22 with Cutter, 3 hole, saddle fold and stitch. I removed...
  16. Re: MX-M904 Finisher Jams in the Saddle Fold entrance area.

    ah ha, ok. I will get one delivered and try it out. I will keep you posted.

    Thanks for all the help.
  17. Re: MX-M904 Finisher Jams in the Saddle Fold entrance area.

    I replaced the sensor. I adjusted the solenoid for the entrance gate. Still jams. I found that the entrance plate on the saddle assembly was crooked a little bit. I loosened it up and re-mounted...
  18. Re: MX-M904 Finisher Jams in the Saddle Fold entrance area.

    I upgraded to the latest firmware. I still get the same finisher jams in the saddle entrance. 2 to 3 sheets usually are jammed at the top transport entrance area. I ran about 40 books and it...
  19. Re: MX-M904 Finisher Jams in the Saddle Fold entrance area.

    The finisher is used. I don't know exactly what you are asking but since its used there have been thousands of sheets through finisher. If you are just asking how many sheets make it when doing the...
  20. Re: MX-M904 Finisher Jams in the Saddle Fold entrance area.

    ok, I have the new firmware so I will go back and try that first.

    I will repost after. Thanks
  21. Re: MX-M904 Finisher Jams in the Saddle Fold entrance area.

    Maybe FNS102_S and FSS203_N and FSS102_S
  22. Re: MX-M904 Finisher Jams in the Saddle Fold entrance area.

    I had the customer scan in the logs.

    They gave me all 6 pages. See the attached.

    Thanks again.
  23. Re: MX-M904 Finisher Jams in the Saddle Fold entrance area.

    Sorry, this may sound stupid. I cant find the jam code for the saddle stitch folder jams. Where does it list the jams?

    They don't use the machine everyday for saddle. so I just now got a...
  24. Re: MX-M904 Finisher Jams in the Saddle Fold entrance area.

    I forgot what the code was. I will have to look when I go back. Stupid me... lol..

    the paper does actually jam. I will read the bulletin you posted but if it is actually jamming and I have to...
  25. MX-M904 Finisher Jams in the Saddle Fold entrance area.

    Hello,

    I have posted here before when asking about this machine model and have since installed it at the customers location. The main body is New out of the box but the finisher FN-22 is used. ...
Results 1 to 25 of 39
Page 1 of 2 1 2