Search:

Type: Posts; User: Cantechman

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    6
    Views
    340

    Re: C3851FS Finisher problems

    I had that exact issue before and I had to take it all apart very carefully, (take pictures) clean and lube the shafts, clean the sensors. They are a real piece of crap.
  2. Thread: Bizhub C558

    by Cantechman
    Replies
    5
    Views
    442

    Re: Bizhub C558

    High voltage board maybe? I had a issue on that model before where black was just a very light grey and it was the HV board.
  3. Replies
    6
    Views
    545

    [Misc] Re: Bizhub C224E

    I would try a new 2nd image transfer roller.
  4. Replies
    23
    Views
    1,490

    Re: bizhub 4050 paper tray empty

    [QUOTE=srvctec;1881372]I'd be willing to bet it's the paper feed clutch as we've replaced a few of those so far (with these exact same symptoms) on these junk machines. It's not too hard to do and...
  5. Thread: Hello there

    by Cantechman
    Replies
    4
    Views
    375

    Re: Hello there

    Could be a variety of things, if it's common to all it could be the transfer belt. It still could be a bad drum or charge corona depending on the colors used. Best to run test samples in service...
  6. Replies
    8
    Views
    632

    Re: Darker black

    Those settings do work, i set that switch with every new i series install i do.
  7. Replies
    10
    Views
    835

    Re: bizhub C250i foggy backgroud printout

    you can try this:
    change switch 153 bit 6

    under pcl driver:
    quality tab/quality adjustment/other/turn pure black off
  8. Replies
    29
    Views
    2,982

    Re: bizhub c300i jam tray 1

    Hasn't been issue since it was replaced.
  9. Replies
    5
    Views
    602

    Bizhub c250i squeaking noise

    I have a c250i with only 20k, it randomly will make a squeaking noise (like a bad bearing type noise) for a minute or so while the machine is not being used, happens very randomly. I couldn't get to...
  10. Replies
    29
    Views
    2,982

    Re: bizhub c300i jam tray 1

    There is a procedure for that particular clutch in the manual. you have to open the "box" not remove the board itself.
  11. Replies
    29
    Views
    2,982

    Re: bizhub c300i jam tray 1

    I never really read what it's function is other then helping transport the paper but's only related to tray one and the bypass I do believe.
  12. Re: konica minolta c360i tray one jam code 1105 also internal error erratic code

    If he changed the whole pickup section and the fast clutch only thing left would be something in the registration section or the baseboard from what i recall.
  13. Replies
    29
    Views
    2,982

    Re: bizhub c300i jam tray 1

    It wasn't that bad, the hardest part is just opening up the baseboard box, I'd say start to finish it took 45 min.
  14. Re: konica minolta c360i tray one jam code 1105 also internal error erratic code

    I'm an old dog as well started in late 90's when there was no such thing as a multifunction machine lol.
  15. [Error Code] Re: Bizhub 4050 Prompt A Trouble Code E301(000.00)

    If the error code does not appear, plug in any applicable cables or add-ons one at a time, waiting at least 30 seconds between any additions. If the code appearswhen the network cable is plugged back...
  16. Re: konica minolta c360i tray one jam code 1105 also internal error erratic code

    Have a look at my thread from a few weeks back. My machine was brand new as well.


    bizhub c300i jam tray 1
  17. Replies
    17
    Views
    1,086

    [Jamming] Re: Bizhub 25e keeps jamming documents

    It's been a while, but I think it's the one i have attached circled. It would randomly stick in the up position.
  18. Replies
    17
    Views
    1,086

    [Jamming] Re: Bizhub 25e keeps jamming documents

    Check the actuator that hangs down. I had one that would randomly stick up in place when it was suppose to move back in position after the sheet was fed. Make sure if moves freely, push it up a...
  19. Replies
    3
    Views
    262

    Re: c3850fs screen blank, machine cycling

    I would start by disconnecting the network and fax cables, I would try and boot into service mode holding down the power button, and if you can update firmware and format the HD. If that doesn't help...
  20. Replies
    29
    Views
    2,982

    Re: bizhub c300i jam tray 1

    The problem was the fast clutch (cl10). It's behind the base board. Once replaced and tested it worked fine.
  21. Replies
    29
    Views
    2,982

    Re: bizhub c300i jam tray 1

    It seemed as though it did for a week or so, must have been a coincedence.
  22. Replies
    29
    Views
    2,982

    Re: bizhub c300i jam tray 1

    it seemed to initially but the customer called back a week later and said it's happening again.
  23. Replies
    29
    Views
    2,982

    Re: bizhub c300i jam tray 1

    [QUOTE=Bix;1680974]Where the paper stop?[/

    Sometimes it doesn't leave the tray, other times it does so no specific place. one or 2 prints seem to be fine it's multiple prints where the issue...
  24. Replies
    29
    Views
    2,982

    Re: bizhub c300i jam tray 1

    I have another complete registration unit to try. It happens intermittently so it's a little difficult to diagnose. If that doesn't work i will try the paper feed roller fast clutch and then finally...
  25. Replies
    29
    Views
    2,982

    Re: bizhub c300i jam tray 1

    Yes did both.
Results 1 to 25 of 182
Page 1 of 8 1 2 3 4