Search:

I've done this to myself a couple of times: On the upper section you latch the right but the left isn't quite latched. You can close the door and it closes. After about 20 pages the door pops open...

None of the door switches appear in U031. We noticed that in addition to:

PCUSW paper conveying unit switch (Feed PWB 1: YC15 pins 1&3, YC1 pin23, YC6 pin42)(signal: INTER_LOCK)

also not...

I'm guessing that these drivers are on a server somewhere and endusers settings are not saved at log-off. That's one step past my experience/expertise. One of the IT guys will have to take it from...

Mine was a C3826 (C368), but I only had a peripheral role. The machine was down and I got handed the fuser to install. This machine had two fusers for that reason to my knowledge. =^..^=

Sorry, I don't know the exact keystrokes off the top of my head. I don't get to do it often enough. Ok, I'll try:

On each PC: Start > search "Devices and Printers" > select print driver > Print...

If each PC has a dedicated user, why not just enter the password right into the driver defaults so it never asks? Whomever uses that PC gets billed.

So I requested that the local IT install a PostScript and a PCL driver, test both, then remove the ones that don't work. I don't know which worked ... I suppose it doesn't matter. That part is...

It's the one behind the paper dust collector. You may find that it's necessary to clean the three sensors in that area. You separate the 2nd transfer assembly from the door to see the three sensors....

I don't know if this is pertinent to your model, but I saw this on an HP T790PS:

Symptoms: "Paper is not loaded correctly. Remove paper and reload." even when no paper is present.
Cause: Paper...

Since the enduser is locked out of Admin functions anyway, I think I've covered my bases by requesting a new PS and a PCL driver installed and tested by the local IT.

Am I correct that Q6675D is a...

Welcome! =^..^=

Enduser admits it hasn't been used in a year. When print job is sent you get "Wrong format ... " message, then 61.01 error.

It prints internal prints with the poor quality that you'd expect after...

Enduser admits it hasn't been used in a year. When print job is sent you get "Wrong format ... " message, then 61.01 error.

It prints internal prints with the poor quality that you'd expect after...

On every machine that can print from USB (or print from PC), I print these:

There were some Kyoceras with fuser alignment issues, that produced a similar effect. Not bizhubs. Just speculating.

I'd try adjusting fuser speed. =^..^=

If it's fuser speed, the buckle is changing as the paper is passing the drum. A misaligned fuser can cause the paper to track to the front or rear causing the paper to pull away from the drum. A4 LEF...

You might look at the Lexmark OEM parts. They ARE for the most part Lexmark rebadges, and the only difference is black, not gray rubber.

Excellent find. We had a new Toshiba 3518A come in with non functional erase lamps. Fortunately on Toshiba you immediately get penny sized football shapes of developer on the drum and copies. We...

I hope he wasn't in a rush ... that thread is 25 months old. =^..^=

Thanks Ken. I knew it was different, but not just how different. =^..^=

**bump**

Maybe I'm wrong ... but I think he means that he's not getting very good black density, not an issue with color registration. My guess is that the main issue is inaccurate translation.

I'm also...

I have seen failures of the tiny gears that counter-rotate the separation tire. I had to take a photo of the gear then drag it as big as it would go to see the missing teeth.

I don't think there...

... and you don't get cf248 codes? Hanabi don't like printing webpages. I would suggest saving your webpages as PDF documents, THEN send them to print. =^..^=

Is the scanner still locked? =^..^=