Search:

Type: Posts; User: skynetto

Page 1 of 10 1 2 3 4

Search: Search took 0.31 seconds.

  1. Replies
    33
    Views
    10,899

    [Error Code] Re: MP C3502 SC554 problem

    You need to use the pico FUSE to reset the error. In wont go away with 5810.
    You need 5810-002 which is disabled. You need the pico Fuse to enable that menu.

    D147-FUSE is the part number
  2. Replies
    22
    Views
    1,474

    Re: Finding previous tech SP access code

    Guys the problem is that the SP to dump NVRAM data is not available in Factory mode. Thats why we need an EEPROM reader.
  3. Replies
    22
    Views
    1,474

    Finding previous tech SP access code

    Hello guys,
    I've been reading some posts where there were some cases of Mfp's brought off lease and the previous tech has changed the SP access code. Well the code is saved in the NVRAM but we...
  4. Re: Mp 4002 printing light in parts that have a large toner area.

    You said you changed developer. Have you used the correct procedure for initializing it?
    Bias has to set up to default and 2 or 3 more corrections.
    Have you used a piece of paper to block toner...
  5. Thread: MPC3000 SC995

    by skynetto
    Replies
    6
    Views
    549

    Re: MPC3000 SC995

    We have 2 issues here for black screen.
    1) The most common. Polygon motor fails and taking the BiCu board with it. As other said if you use a torch on the display or use WIM you'll see SC202. Repair...
  6. Replies
    6
    Views
    531

    Re: MP 9002 Smearing

    Try to clean the frame above trasfer belt unit. Too much toner builds there and cause unfused toner to smear before paper reaches fusing unit. Worth to try.
  7. Update on SC345 on MP6000/6001 SP9100 series

    Hi folks,
    Lately i had the same problem on a SP9100. By browsing all the posts about this problem (fly wheel loose, drum shaft connector ecc) and checking all these solution my problem was always...
  8. Replies
    6
    Views
    591

    Re: ricoh mpc 2051

    Use oem toner.
  9. Replies
    4
    Views
    1,224

    Re: : MPC 3500 with SC491

    Check bias drum pin on the machine side. Happens to me last week on the black one. Someone has taken the PCU out and bend the pin on the frame of the machine.
  10. Re: C3300 development clutch (I may be screwed)

    Get you hands dirty and take out that drive group. No easy way to do it. :)
  11. Replies
    10
    Views
    3,217

    Re: Ricoh MPC5000 Part Transfer Assembly Holder

    Yep. Same part.
  12. Replies
    10
    Views
    3,217

    Re: Ricoh MPC5000 Part Transfer Assembly Holder

    Here it is.
    34078
  13. Replies
    5
    Views
    853

    Re: cypher sc 995 mpc 3000

    Replace the fuser. It has blown even if you dont see nothing damaged. It gives continuity on board but infinite off board.
  14. Replies
    9
    Views
    676

    [Dead] Re: MPC6501 dead with only power on light

    You got a dead MPC6501? Hooray. It can't be repaired :)
    If you really want to repair it check the control panel. On the MPC2050, which have the same symptom, after replacing everything it was the op...
  15. Replies
    6
    Views
    1,527

    Re: Mpc3300 j026 duplex jams?

    Replace duplex gate. Can't remmeber the part code but if you take it away and have a look at it you'll see that the heat has bend the plastic. There is a rtb about this.
  16. Thread: MP C 5000

    by skynetto
    Replies
    2
    Views
    426

    Re: MP C 5000

    Same as MPC2800. Have used the same parts for mpc2800 one year ago and it is still working.
  17. Replies
    6
    Views
    600

    Re: MP C6501 (aka duster producer)

    Thanks a lot. I have only two left.
    @SlimSlob: I'm using your settings also with good results. Let's see if this frimware update makes things better.
  18. Replies
    6
    Views
    600

    MP C6501 (aka duster producer)

    Downloaded today from Ricoh Portal a new Engine firmware [Version] 1.11:06 with these modifications:

    Does anybody have the RTB they are talking about?

    Thanks in advance.
  19. Re: Ricoh MP 4500 Development Unit - what is the (RJ 45- like) plug for?

    Not only. It handles the TD sensor also
  20. Thread: mp c4500

    by skynetto
    Replies
    21
    Views
    1,473

    Re: mp c4500

    The machine is heavily undertoner. So the things you have to try....again....in order are:

    1) New toner bottle (even the one you have is new)
    2) New pump and new tube
    3) New Developer / PCU unit...
  21. Replies
    7
    Views
    720

    Re: MP C4500 K pump same as Y?

    If you look carefully (at least on a mpc4500) the yellow pump has the angle almost facing up while the other colours (b,m,c) have an angle of 45 degrees. The problem is not with the pump itself but...
  22. Thread: mp c4500

    by skynetto
    Replies
    21
    Views
    1,473

    Re: mp c4500

    Wich colour i affected? Be careful with the tube beeing blocked by itb if the wrong pump is installed in the wrong place, for example placing black pump in the yellow place, its tube will be blocked...
  23. Thread: mp c4500

    by skynetto
    Replies
    21
    Views
    1,473

    Re: mp c4500

    Again check 3201 and 3222 and post here the values.
  24. Thread: mp c4500

    by skynetto
    Replies
    21
    Views
    1,473

    Re: mp c4500

    Ok. You cant resolve this kind of problem with a firmware upgrade. Check 3222 and 3201 for the affected colour. Also when doin a force toner check if 3201 lowers down or goes up. Does the toner...
  25. Thread: mp c4500

    by skynetto
    Replies
    21
    Views
    1,473

    Re: mp c4500

    Change developer and/or check dev gears if broken
Results 1 to 25 of 241
Page 1 of 10 1 2 3 4