Page 2 of 3 FirstFirst 123 LastLast
Results 11 to 20 of 25
  1. #11
    Senior Tech 250+ Posts spanky's Avatar
    Join Date
    Sep 2012
    Location
    Md
    Posts
    304
    Rep Power
    20

    Re: Sharp MX-M904 Still Good?

    You must install a bypass tray, the MX-MF11 since you have the MX-LC13 attached to the machine.

  2. #12
    Technician
    Join Date
    Aug 2015
    Location
    Camp Hill, PA
    Posts
    39
    Rep Power
    9

    Re: Sharp MX-M904 Still Good?

    Quote Originally Posted by spanky View Post
    You must install a bypass tray, the MX-MF11 since you have the MX-LC13 attached to the machine.
    Ohhhh. Ok, thanks for the info. I will look around for one or if anyone has one let me know.

    Thanks

  3. #13
    Technician
    Join Date
    Aug 2015
    Location
    Camp Hill, PA
    Posts
    39
    Rep Power
    9

    Re: Sharp MX-M904 Still Good?

    Wait, I do have the bypass tray on the MX-LC13. It's mounted on the top of the two trays. I just don't have the door or the transport for the main unit. So when paper feeds from tray 5 or 6 it stops on the feed rollers in the main unit because there is no upper transport with idlers to push down on the feed tires. Paper just lays in the feed tires and declares a jam. I need the upper part of that section. Is there a part number for it ? or does it actually come with the bypass tray ? Either way I need one.

    Let me know what I can do to get one if you have any idea. I am looking around other places that may have a parts machine I can get it from.

    See the pictures attached. The finisher in the picture was replaced with the Fn-22 and the Fn-21 was removed.

    The picture of the right side of the main unit shows no upper transport over the entrance feed rollers. This is what I need.

    Thanks
    Attached Images Attached Images

  4. #14
    Senior member of CRS 2,500+ Posts
    Sharp MX-M904 Still Good?

    ZOOTECH's Avatar
    Join Date
    Jul 2007
    Location
    Insane Diego, CA
    Posts
    3,165
    Rep Power
    90

    Re: Sharp MX-M904 Still Good?

    You may need the LCT Mounting kit (RB16), if I remember correctly.
    "You can't trust your eyes, if your mind is out of focus" --

  5. #15
    Technician
    Join Date
    Aug 2015
    Location
    Camp Hill, PA
    Posts
    39
    Rep Power
    9

    Re: Sharp MX-M904 Still Good?

    ok, thanks I'll take a look and see if I can locate one.

    If anyone knows where to get one let me know.

    Thank you all.

  6. #16
    Technician
    Join Date
    Aug 2015
    Location
    Camp Hill, PA
    Posts
    39
    Rep Power
    9

    Re: Sharp MX-M904 Still Good?

    Is this the kit that you are talking about ? I want to make sure before I bid on it.

    Brand New Sharp MX-RB16 Large Capacity Tray Paper Pass Module | eBay

    Thanks

  7. #17
    Senior member of CRS 2,500+ Posts
    Sharp MX-M904 Still Good?

    ZOOTECH's Avatar
    Join Date
    Jul 2007
    Location
    Insane Diego, CA
    Posts
    3,165
    Rep Power
    90

    Re: Sharp MX-M904 Still Good?

    Quote Originally Posted by acribari View Post
    Is this the kit that you are talking about ? I want to make sure before I bid on it.

    Brand New Sharp MX-RB16 Large Capacity Tray Paper Pass Module | eBay

    Thanks
    I believe that is the one, but you should check with a current tech/dealer - I've been retired 3.5 years without access to latest bulletins.
    "You can't trust your eyes, if your mind is out of focus" --

  8. #18
    Junior Member
    Join Date
    Sep 2019
    Location
    dubai
    Posts
    1
    Rep Power
    0

    Re: Sharp MX-M904 Still Good?

    Nice information,
    laptoprental.ae

  9. #19
    Technician
    Join Date
    Aug 2015
    Location
    Camp Hill, PA
    Posts
    39
    Rep Power
    9

    Re: Sharp MX-M904 Still Good?

    Ok, I finally got the machine all installed and it has been running good. I had some issues with the finisher but I got that resolved.

    Now, I need to use the Raw copy tool and an SD card to copy the on board SD card. I want to make sure I do it correctly.

    Can you give me a step by step instruction on this?

    Do I leave the original SD card in the machine and use the USB port with a laptop or do I remove the SD card and plug it in the laptop to copy it?

    Do I need to have my blank SD card and the Original SD card plugged in the laptop at the same time?

    Or do I copy the original image to the laptop first and then write it to the blank SD card?

    I just want to be clear on this before I do something wrong.

    If you can give me step by step instructions that would be great.

    Also, I am guessing this is a regular SD card and not a Micro SD card? I ordered a Regular size SanDisk 16GB class 10 SD card.

    Thanks in advance.

  10. #20
    Service Manager 5,000+ Posts
    Sharp MX-M904 Still Good?

    Phil B.'s Avatar
    Join Date
    Jul 2016
    Location
    Raleigh NC
    Posts
    5,393
    Rep Power
    96

    Re: Sharp MX-M904 Still Good?

    Quote Originally Posted by laptoprental View Post
    Nice information,
    laptoprental.ae
    Advertising - Posting or replying to posts for the express purpose of referring others to another commercial website is not allowed, If you want to advertise here please see this link (our paid advertisers are exempt from this rule but please don't over do it).


    please refrain from similar posts.. you have been reported

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here