Page 2 of 2 FirstFirst 12
Results 11 to 20 of 20
  1. #11
    Technician
    Join Date
    Aug 2015
    Location
    Camp Hill, PA
    Posts
    39
    Rep Power
    9

    Re: Sharp MX-M904 Image Shift

    Quote Originally Posted by Hansen88 View Post
    It looks like according to the operating guide that for 12x18 you would need to manually set the size for the bypass tray under type and size. Otherwise try the 50-22 auto size adjustment for the bypass.
    Ok I will give it a try.

    I posted at the same time you did. Make sure we are talking about the same bypass model.

    Thanks

  2. #12
    Senior Tech 250+ Posts
    Join Date
    Dec 2009
    Location
    Waukegan IL
    Posts
    351
    Rep Power
    26

    Re: Sharp MX-M904 Image Shift

    Ok sounds like that is a unit I have not worked on. I was thinking standard type bypass. Not sure on any help I can give.

  3. #13
    Technician
    Join Date
    Aug 2015
    Location
    Camp Hill, PA
    Posts
    39
    Rep Power
    9

    Re: Sharp MX-M904 Image Shift

    Does anybody have an answer for this issue?

    I need to center the image on 12 X 18 and all other paper sizes from the multi bypass tray. The bypass is Model MX-MF11 and sits on top of the high capacity trays 5 and 6.

    Is there any way to adjust the centering of the image? I can only get it to move the image down and not up. I need it to move at least 1/4 inch from the bottom. I can only shift it in the software and it only allows me to move the image closer to the bottom edge of the paper.

    Is there a mechanical adjustment? Maybe a set up mistake?

    I need some clues if you have any.

    Thanks in advance.

  4. #14
    Senior Tech 250+ Posts spanky's Avatar
    Join Date
    Sep 2012
    Location
    Md
    Posts
    304
    Rep Power
    20

    Re: Sharp MX-M904 Image Shift

    Does the copier read the proper size of the paper you are loading on the bypass tray.

    If not the service manual says

    Press the [Tray Paper Settings] key on the operation panel to
    select paper sizes that are not detected automatically by the combination
    of paper size and paper length sensor readings

  5. #15
    Senior Tech 250+ Posts spanky's Avatar
    Join Date
    Sep 2012
    Location
    Md
    Posts
    304
    Rep Power
    20

    Re: Sharp MX-M904 Image Shift

    I just read earlier in your thread the paper size was reading properly.

    Have you tried adjusting the centering with sim 50-10?

  6. #16
    Technician
    Join Date
    Aug 2015
    Location
    Camp Hill, PA
    Posts
    39
    Rep Power
    9

    Re: Sharp MX-M904 Image Shift

    No I have not tried sim 50-10. The high cap trays are centered so will this mess them up if I use sim 50 -10?

    I can go back and give it a try.

    They are running 80 pound card 12X18 and it does see the size on the display panel. I can select bypass tray and it shows 12X18 heavy stock.

    I can feed out of tray 5 and 6 and it is centered. But after a few sheets it jams from those trays. So I am hoping after I get the bypass centered it will not jam feeding from that unit.

    I will try sim 50-10 and see if it works out.

    Thanks for the tip. I am desperate at this point. Lol... Thank you!

  7. #17
    Senior Tech 250+ Posts spanky's Avatar
    Join Date
    Sep 2012
    Location
    Md
    Posts
    304
    Rep Power
    20

    Re: Sharp MX-M904 Image Shift

    In sim 50-10 you can choose which tray (including bypass tray) you want to adjust.

    All other trays will not be affected.

  8. #18
    Technician
    Join Date
    Aug 2015
    Location
    Camp Hill, PA
    Posts
    39
    Rep Power
    9

    Re: Sharp MX-M904 Image Shift

    Thank you very much for the info. I went to the account today and ran 50-10 on HCT Bypass tray and the data setting was on 48. I had to move it to 95 and now its perfectly centered on 12 X 18 and all other paper sizes.

    Thanks again. You saved me. lol.... I really apricate your advice.

    For some reason they don't have the tray adjustment listed when you install the bypass unit. It just tells you to install it and how. I could not find a place in the service manual for this adjustment until I asked you on this forum. Seems odd that they would not run you through this on the installation.

    Thank You !!!!!!

  9. #19
    Senior Tech 250+ Posts spanky's Avatar
    Join Date
    Sep 2012
    Location
    Md
    Posts
    304
    Rep Power
    20

    Re: Sharp MX-M904 Image Shift

    The adjustment is covered during training.

  10. #20
    Technician
    Join Date
    Aug 2015
    Location
    Camp Hill, PA
    Posts
    39
    Rep Power
    9

    Re: Sharp MX-M904 Image Shift

    Quote Originally Posted by spanky View Post
    The adjustment is covered during training.

    Ah, that makes sense. I did not have any formal training on this model. Just have the service documentation. Thanks for all the help.


Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here