Thanks Thanks:  0
Dislikes Dislikes:  0
Results 1 to 7 of 7
  1. #1
    Technician
    Join Date
    Oct 2007
    Location
    North Palm Beach
    Posts
    34
    Rep Power
    26

    MX M453 "Remove paper from offset tray"

    I know this is a stupid question. But just replaced FN X9. Copier say to remove paper from offset tray after a print job then a copy job started. The customer has to turn the machine off to reset.
    I haven't looked at the exit tray sensor yet. I am not sure why the machine wouldn't allow continuous copy even with paper in the exit tray.
    Could it be the security software on the copier. Or do I need to just go there and look at the sensor.
    I feel like it might be something Sharp crazy.
    Has anyone had an issue like this. Thanks for the info.

  2. #2
    Service Manager 1,000+ Posts bilyahn's Avatar
    Join Date
    Dec 2006
    Location
    Quincy, CA
    Posts
    1,265
    Rep Power
    43

    Re: MX M453 "Remove paper from offset tray"

    If I remember correctly the FN9 went to several different series machines and after installing Sharp recommended upgrading the firmware. Had a lot of odd issues that were resolved by a firmware upgrade with this generation.

    Good luck.

    Bil

  3. #3
    Field Supervisor 500+ Posts
    MX M453 "Remove paper from offset tray"

    copiertec's Avatar
    Join Date
    Jan 2016
    Location
    Centereach, L.I. New York
    Posts
    793
    Rep Power
    27

    Re: MX M453 "Remove paper from offset tray"

    Agreed with bilyhahn, is the firmware up to date?

  4. #4
    Technician
    Join Date
    Oct 2015
    Posts
    26
    Rep Power
    10

    Re: MX M453 "Remove paper from offset tray"

    It may be the harness. They break along the vertical gudie. Located under the tray, rear side. It bends, and sometimes wears out the wire.

  5. #5
    Senior Tech 250+ Posts
    MX M453 "Remove paper from offset tray"


    Join Date
    Dec 2009
    Location
    Waukegan IL
    Posts
    447
    Rep Power
    32

    Re: MX M453 "Remove paper from offset tray"

    I dont see any kind of settings that could cause that message. The only thing I can think of is the exit sensor on the output unit is bad or the sensor actuator is stuck making machine think there is paper there.

  6. #6
    Senior Tech 250+ Posts
    Join Date
    May 2010
    Location
    Dallas, TX
    Posts
    301
    Rep Power
    26

    Re: MX M453 "Remove paper from offset tray"

    replace the tray height sensors...i believe there are 3 and check the harness to the paper detect sensor on the tray. if the harness is not routed correctly it can get stretched and will cause that error.

  7. #7
    Junior Member
    Join Date
    May 2019
    Location
    San diego
    Posts
    6
    Rep Power
    0

    Re: MX M453 "Remove paper from offset tray"

    Check the 3 height sensors like repn1999 said and look at the harness, Ive had some of those rip and cause that issue. You can also go into sim mode to test out the sensors and see if one specifically is not working properly. Off the top of my head its sim 3-3 or 3-2 but I might be wrong.

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here