MX-3110N Faded Prints, Copies Good

[copiertec]

donations? some that have received MAJOR help don't. Stating 'well I will never need this service again.'

or the newbie techs SOME that have already started more than 3 threads all on different machines and still don't donate.

Sad but true. Eventually, the end user can only go so far without having a trained tech come out to resolve the issue, it's inevitable. I make a list of the ones that use us for info and I refuse after a certain point to help them out without a site contribution.

[Phil B.]

Sad but true. Eventually, the end user can only go so far without having a trained tech come out to resolve the issue, it's inevitable. I make a list of the ones that use us for info and I refuse after a certain point to help them out without a site contribution.

mind if I steal that personal policy .. sounds golden!

[Phil B.]

I'm sorry I loose you at storing/calling of system settings

do us all a favor...

1) make a small contribution to keep CTN running

2) post a manual request here----> https://www.copytechnet.com/forums/s...nual-requests/

the contributor badge will show the guys with the manuals that:
1) you made a contribution
2) you are likely to get quicker service on your request

you seem to be stumbling with simple things .. the manual is your best recourse .. Copiertec and I have tried n tried

hell 5 PAGES to this thread and the thread is only 1 day old.

another suggestion is to HIRE a TRAINED tech..

you've gotten alot of help for NADA - ZIP - ZILCH so far.

some people shouldn't try to fix their own machines.

[mioduz]

At the control panel, (System) settings, login as admin (all lower case), storing/calling of system settings, restore factory settings, execute.

Sorry I swear I looked that list up and down, and couldn't find this, but alas it was right there in front of my face.

Completed, no change

[chubblies]

Try 46-74 for both copy and print. Also check 26-18 for TS mode is off. If not this might be the SD card. Had the same on a MX2310 where you would calibrate it, it would try to save the calibration to the SD but it would fail, so it would revert back to factory settings, but only on print...

[copiertec]

do us all a favor...

1) make a small contribution to keep CTN running

2) post a manual request here----> https://www.copytechnet.com/forums/s...nual-requests/

the contributor badge will show the guys with the manuals that:
1) you made a contribution
2) you are likely to get quicker service on your request

you seem to be stumbling with simple things .. the manual is your best recourse .. Copiertec and I have tried n tried

hell 5 PAGES to this thread and the thread is only 1 day old.

another suggestion is to HIRE a TRAINED tech..

you've gotten alot of help for NADA - ZIP - ZILCH so far.

some people shouldn't try to fix their own machines.

Very eloquently written, sir. I am now unsubscribed from this thread.

[OlliK1969]

Hi

sometimes the problem is in front of the device

[mioduz]

Try 46-74 for both copy and print. Also check 26-18 for TS mode is off. If not this might be the SD card. Had the same on a MX2310 where you would calibrate it, it would try to save the calibration to the SD but it would fail, so it would revert back to factory settings, but only on print...

I can confirm that toner save is turned off for all modes

46-74 I ran and found the output a bit confusing

https://i.imgur.com/PSQEhlu.jpg

Seams like the corrected patch is faded. Maybe I'm off here but the original patch seams accurate

[chubblies]

Seams like the corrected patch is faded. Maybe I'm off here but the original patch seams accurate

Try a SD. You should be able to take an image from it even if it is defective, and a new card should allow the read/writeing which will apply the calibration to it. Worth a £5 SD to try

[mansart]

Try the following.....

Do test print SIM 64-5, then do a test print with SIM 64-2.

Are they both light? Or is one better than the other?

These test prints originate from different boards and can point you in the right direction.