Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Page 1 of 2 12 LastLast
Results 1 to 10 of 14
  1. #1
    Technician
    Join Date
    Jul 2010
    Posts
    17
    Rep Power
    23

    Exclamation witch sharp model is recommended for a +100K prints per month?

    monocrome and with finisher...

    with new sharp model would you recommend?
    i'm a new sharp dealer... any ideas?

  2. #2
    Senior Tech 250+ Posts harleyrider's Avatar
    Join Date
    Oct 2011
    Location
    ,il
    Posts
    348
    Rep Power
    25

    Re: witch sharp model is recommended for a +100K prints per month?

    mx-m623 or 753. As per finisher it would depend on what you need- there is a couple for these models.

  3. #3
    Senior Tech 100+ Posts PASTech's Avatar
    Join Date
    Sep 2010
    Posts
    192
    Rep Power
    25

    Re: witch sharp model is recommended for a +100K prints per month?

    Quote Originally Posted by harleyrider View Post
    mx-m623 or 753. As per finisher it would depend on what you need- there is a couple for these models.
    Agreed
    What's Brown and Sticky?

    -A Stick

  4. #4
    Technician
    Join Date
    Jul 2010
    Posts
    17
    Rep Power
    23

    Re: witch sharp model is recommended for a +100K prints per month?

    are they reliable?


    thanks for the prompt response!

  5. #5
    Senior Tech 100+ Posts PASTech's Avatar
    Join Date
    Sep 2010
    Posts
    192
    Rep Power
    25

    Re: witch sharp model is recommended for a +100K prints per month?

    Quote Originally Posted by mad View Post
    are they reliable?thanks for the prompt response!
    We put in two MXM753's last year into a large High School, we have had very little problems with them other than use induced jams or damage to fuser from the wrong transparencies.They seem to be pretty solid.One thing you need to do is plug the machines in for at least 24 hours prior to assuming they are good. We did get one of these machines in and it tested fine in shop and then a week later when we installed the HV power board was Dead. This according to sharp was a rare occurance with all machines where a board broke from the current running through a bad connection on that board. They said that one was we can make sure that it is good before you take any large copier is to plug it in for at least 24 prior. Doesn't stop the deadness but at least you don't tell the customer it is ready and then bam it is dead.This is not a slam on this machine, the ones in the school have done really well. Just seems to be a problem with circuitry when the machine get shipped way up north here.Hope that helps, I would say go ahead and sell them these machines! they are next generation, ARm550's which we have many out there pushing well beyond their lease. Solid Machines!
    What's Brown and Sticky?

    -A Stick

  6. #6
    Senior Tech 100+ Posts
    Join Date
    Jul 2011
    Posts
    143
    Rep Power
    22

    Re: witch sharp model is recommended for a +100K prints per month?

    I think i would perfer the hercules machines we have at least 7 that are at 100k plus per month. All the supplies go past the recomened yields. Must replace feed rollers every pm. Most have the smaller finishers.

  7. #7
    Technician
    Join Date
    Jul 2010
    Posts
    17
    Rep Power
    23

    Re: witch sharp model is recommended for a +100K prints per month?

    which models are the hecules family?

  8. #8
    Legendary Frost Spec Tech 2,500+ Posts
    witch sharp model is recommended for a +100K prints per month?

    Akitu's Avatar
    Join Date
    Oct 2010
    Location
    Thompson, MB
    Posts
    2,596
    Rep Power
    91

    Re: witch sharp model is recommended for a +100K prints per month?

    MXM850/950/1100...

    If you're holding out for a Hercules unit, might as well wait it out and grab a Hercules 2 when they become available.
    Cthulhu for president! Why settle for the lesser evil?

  9. #9
    Senior Tech 100+ Posts
    Join Date
    Jul 2011
    Posts
    143
    Rep Power
    22

    Re: witch sharp model is recommended for a +100K prints per month?

    They are available,just set up a 1204 in our office yesterday. The main body is pretty much the same. But they did use the aries touch screen. The new models are 904,1054,1204

  10. #10
    Senior member of CRS 2,500+ Posts
    witch sharp model is recommended for a +100K prints per month?

    ZOOTECH's Avatar
    Join Date
    Jul 2007
    Location
    Insane Diego, CA
    Posts
    3,277
    Rep Power
    94

    Re: witch sharp model is recommended for a +100K prints per month?

    Quote Originally Posted by Akitu View Post
    MXM850/950/1100...

    If you're holding out for a Hercules unit, might as well wait it out and grab a Hercules 2 when they become available.
    Agreed, but he may find "close out" deals from Sharp to clear out their inventory.
    "You can't trust your eyes, if your mind is out of focus" --

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here