Dear,
My copier E-studio 2050C have a 101 Error and i have think that it's the hard disk broken, whan i found the procedure for change hard disk and the firmware ?
best regard's
Dear,
My copier E-studio 2050C have a 101 Error and i have think that it's the hard disk broken, whan i found the procedure for change hard disk and the firmware ?
best regard's
If I were you, I think I'd read that section of the manual. It's very helpful. =^..^=
If you'd like a serious answer to your request:
1) demonstrate that you've read the manual
2) demonstrate that you made some attempt to fix it.
3) if you're going to ask about jams include the jam code.
4) if you're going to ask about an error code include the error code.
5) You are the person onsite. Only you can make observations.
blackcat: Master Of The Obvious =^..^=
Hello all.
Today my copier 2050c shows F101 7 error, after several general power cut of and power on from the main power of the building.
Initially shows F101-7 error, after C5 apply the error changes to F101-1 and not enter to menus.
I need the firmware?
Same machine was fully backed up in 2019 with a new hard drive and T210SF0W2190 FW
The amount of copy/print was below 6k pages from then
Please advice.
1. Turn the power of the equipment OFF and check the
connection of the HDD.
- Connector and harness check
- Check if the connector pins of the HDD are bent.
- Check if HDD for other equipment is not installed.
- Check if SRAM for other equipment is not installed.
2. If the error still occurs after step 1, perform the following.
- Perform [3C] - [5] (Key Backup Restore) and check
that each Key Status is "OK".
- If not, recover the key (copy "SRAM Key Status" to
"FROM Key Status" or vice versa).
3. If the error persists after step 2, perform
[5]+[C]+[POWER]2. Recovery F/S6. /imagedata,
and then restart the equipment.
4. If the error persists after step 3, perform
[5]+[C]+[POWER]3. Initialize HDD5. /imagedata,
and then restart the equipment.
5. If the error still persists after step 4, perform the
following.
- Perform [3C] - [3] (Format HDD), and then install
"System Software (HD data)" with [49] - [4].
Notes:
The following items will be deleted by performing
[3C] - [3] (Format HDD).
• Message Log
• Job Log
• Spool Data (Print, Email reception)
• Template
If the error persists after performing step 5, perform
step 5 after performing [4]+[C]+[POWER]1. Revert
factory initial status HDD.
6. If the error persists even after step 5, replace the HDD.
7. If the error persists even after step 6, replace the SATA
harness.
8. If the error persists even after step 7, replace the SYS
board.
Sram key status BROKEN
From key status NULL
what to do?
[D] Restore ADI key
Perform the following procedures if the ADI-HDD has been installed.
(1) Turn the power ON while pressing [3] and the [CLEAR] button simultaneously.
(2) Enter the password, and then press the [OK] button.
(If the password is not set for Service, press the [OK] button without entering anything.)
(3) Key in [5] to select “5. Key Backup Restore”, and then press the [START] button.
(4) Key in [5] to select “5.ADIKey SRAM to FROM”, and then press the [START] button.
(5) Wait until the restoring of the encryption key is completed. “Operation Complete” is displayed.
(6) Restart the equipment after the restoring is completed. If you want to perform the restoring of the
encryption key, do not restart the equipment but perform from (4) in “[E] Restore encryption key”.
[E] Restore encryption key
(1) Turn the power ON while pressing [3] and the [CLEAR] button simultaneously.
(2) Enter the password, and then press the [OK] button.
(If the password is not set for Service, press the [OK] button without entering anything.)
(3) Key in [5] to select “5. Key Backup Restore”, and then press the [START] button.
(4) Key in [1] to select “1. Key SRAM to FROM”, and then press the [START] button.
(5) Wait until the restoring of the encryption key is completed. “Operation Complete” is displayed.
(6) Turn the power OFF after the restoring is completed.
If you want to perform the restoring of the license, do not turn the power OFF but perform from
(4) in “[F] Restore license”.
[F] Restore license
(1) Turn the power ON while pressing [3] and the [CLEAR] button simultaneously.
(2) Enter the password, and then press the [OK] button.
(If the password is not set for Service, press the [OK] button without entering anything.)
(3) Key in [5] to select “5. Key Backup Restore”, and then press the [START] button.
(4) Key in [3] to select “3. License SRAM to FROM”, and then press the [START] button.
(5) Wait until the restoring of the license is completed. “Operation Complete” is displayed.
(6) After the restoring is completed, check that “OK” is indicated in “SRAM License STATUS” and
“FROM License Status”. Then, turn the power OFF.
(7) If “4. License FROM to SRAM” is performed by mistake, carry out the following procedure.
P. 9-39 "[ 1 ] Re-registration when the board is replaced"
Bookmarks