Dislikes:
0
-
Work centre 7830 blank display and all lights on
I don't usually work on xerox but it has been very slow for me.
I had a look at this machine yesterday and re-seated connectors on what appears to be the main board. Pulled out the
network board assembly. Dis-connected the pedestal feeder and doc fdr. Checked the battery voltage on that board. It's
reads 3.123vdc. Check the reset button by the power cord and pressed the reset on the network board.
None of these things helped. When the power comes up the only thing that comes on is a small fan in the back. No motors
and all the lights on the control panel are on. No beeps when the buttons are pushed. I did pull the control panel and had
a look but did not take it apart.
I did see something on the internet about using an alt boot. It's my understanding that the machine may be able to boot from
the usb. And this would indicate a bad HDD. I also saw where it may be possible to get the firmware right off the xerox website.
Am I on the right track?
I don't have a manual and would like to have one.
And I don't have a source for parts on this machine.
Any help would be helpful.
Thanks
DR
-
Re: Work centre 7830 blank display and all lights on
Put the .DLM file on a USB in a folder called "altboot" also create a text file with no extension called "FORCED_UPGRADE" inside the altboot folder.
-
Re: Work centre 7830 blank display and all lights on
Thank you for that info. I will try to find the firmware next.
Anyone got a book I could borrow for this machine?
Thanks
DR
-
Re: Work centre 7830 blank display and all lights on
InterfaceP,
I have a 1gig thumb drive and I have unzipped the firmware and clone folders inside the altboot folder. I don't understand
how to create a file without an extension?
I used word pad to create a file named forced_upgrade and it put the txt extension on the file. I always thought every file
needed an extension to indicate the program needed to open it.
As you may have guessed my computer skills are kinda dull.
I did see something on the internet about a "0" file. But now I can't find it.
Thanks
DR
-
Re: Work centre 7830 blank display and all lights on
Check small led display at back side of machine.
Post here letter or number which you have on display.
-
Re: Work centre 7830 blank display and all lights on
Thanks Xcopytech. Wilco.
DR
-
Re: Work centre 7830 blank display and all lights on
Xcopytech,
I did see this machine today and the display shows the number 5. I saw where it indicates the SD card
could be at fault. It has been re-seated with no change.
I also looked at the SBC bd LED's.
CR4 the heartbeat is on and pulses slow, when the soft switch is on it is slightly faster.
CR8 and 10 are both on steady and so is CR5. All lights are green.
Those are the only LED on the SBC bd that are on.
It sez the boot code resides on the SD card.
I have an usb (1G) I'm not sure it is set up correctly. I'll post more later.
Thanks
DR
-
Re: Work centre 7830 blank display and all lights on
If you have code 5 and your display is blank (white) then you have to replace SD card and altboot machine.
-
Re: Work centre 7830 blank display and all lights on
Xcopytech,
This SD card is it something special or can I just get one from Frys electronics? I'm concerned about the altboot set up on the thumb drive.
I have a folder on the drive named altboot.
Inside altboot folder is a folder named workcentre7830-35-sw07201000409100 and a notepad file
called forced upgrade.
Inside the workcentre 7830-35-sw07201000409100 folder is another folder named clone patch and two other file's named
snmp.dlm and workcentre 7830-35-sw#07201000409100#
Inside the clone_patch folder are two files one is a read me and the other is clonefixvl.dlm
Does that sound right?
Thanks
DR
-
Re: Work centre 7830 blank display and all lights on
Just create folder called altboot and put dlm file in.
7830-35 dlm file and notepad file forced upgrade.
Dlm file must be in altboot folder.
You have to buy sd card from xerox.
First try altboot
Tags for this Thread
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
Bookmarks