Xerox WC 7830 Developer change

[LATechnico]

Hi guys,

I have a Xerox WC 7830i that was over adding and dumping Cyan toner. I've decided to change the developing unit and developer. Do I need to run a set up procedure for new developing unit? Or should it print ok without a set up. Not familiar with Xerox, any help is greatly appreciated!

[Phil B.]

Hi guys,

I have a Xerox WC 7830i that was over adding and dumping Cyan toner. I've decided to change the developing unit and developer. Do I need to run a set up procedure for new developing unit? Or should it print ok without a set up. Not familiar with Xerox, any help is greatly appreciated!

any xerox I have worked on yes you need to run an init setup.

do you have the manual? NEEDED FOR WORKING ON THESE POS's

[LATechnico]

any xerox I have worked on yes you need to run an init setup.

do you have the manual? NEEDED FOR WORKING ON THESE POS's

Haha, thanks for the reply. Just downloaded the manual, hopefully the info is there. Business is still slow so not turning down any work even if I gotta deal with some headaches!

[weetu]

Hi guys,

I have a Xerox WC 7830i that was over adding and dumping Cyan toner. I've decided to change the developing unit and developer. Do I need to run a set up procedure for new developing unit? Or should it print ok without a set up. Not familiar with Xerox, any help is greatly appreciated!

You have to go to Diagnostics and enter the ATC (Automatic Toner Control) value in the system. Normally it is somewhere around 50. The value is the ATC sensor's value got at manufacture and it is unique to the sensor which comes in the new Developer Assy.
You will find the value printed on a small sticker attached to the bottom of Developer housing. Write it down for further use.

The machine will run with wrong value however, but if you really need good color balance you MUST enter the value and run the setup routine. Otherwise you'll finally end up with the dumping issue.
I suggest you check first the present value if it is terribly wrong.


Good luck.

[LATechnico]

You have to go to Diagnostics and enter the ATC (Automatic Toner Control) value in the system. Normally it is somewhere around 50. The value is the ATC sensor's value got at manufacture and it is unique to the sensor which comes in the new Developer Assy.
You will find the value printed on a small sticker attached to the bottom of Developer housing. Write it down for further use.

The machine will run with wrong value however, but if you really need good color balance you MUST enter the value and run the setup routine. Otherwise you'll finally end up with the dumping issue.
I suggest you check first the present value if it is terribly wrong.



Good luck.

Awesome info, what's the procedure for accessing the diagnosis mode?

[Phil B.]

Awesome info, what's the procedure for accessing the diagnosis mode?

it's in the damn MANUAL! you shouldn't be working on ANY Xerox box without one!

[LATechnico]

it's in the damn MANUAL! you shouldn't be working on ANY Xerox box without one!

Well! What do we have here? A ___ comedian? Haha

I do agree with you Phil B, I'll definitely be looking up the manual when I work on this beautiful machine.

[Phil B.]

Well! What do we have here? A ___ comedian? Haha

I do agree with you Phil B, I'll definitely be looking up the manual when I work on this beautiful machine.

not a comedian AH.

I have been working on Xerox crap for the past 28 years...31 years total in the industry. they are getting more difficult to work on AND impossible without the manual and PWS.

put in a manual request here: https://www.copytechnet.com/forums/s...nual-requests/

but don't worry you won't have to deal with the comedian any longer.

[LATechnico]

not a comedian AH.

I have been working on Xerox crap for the past 28 years...31 years total in the industry. they are getting more difficult to work on AND impossible without the manual and PWS.

put in a manual request here: https://www.copytechnet.com/forums/s...nual-requests/

but don't worry you won't have to deal with the comedian any longer.

Thanks Phil. I started on Minoltas back in '92 myself but rarely work on anything bigger than a desktop for the last 15 years. I've tried other business but the printers are still my bread n butter.
Are you retiring? Or changing industries?

[weetu]

Awesome info, what's the procedure for accessing the diagnosis mode?

Press and HOLD <STOP> button for 10 seconds. Then enter 6,7,8,9.

The machine has to be in normal copying state eg. Services, E-Mail etc. visible on the touch screen.
Don't reset anything while in Service Mode. You just want to enter the ATC value, eh?

GL