IRADV 8095 E 302-001

[julka123]

Hi all,
I have a problem with the photocopier iradv 8095 with error E302-0001. are the connections to reader controller ok.Copy of glass is ok.
Copying from the document feeder causes an error .

any ideas

[vigour]

Re: IRADV 8095 E 302-001

E302-0001 refers to Front side scanning
I think there is a break in your flex cable which shows up when scanner reaches the slide read position
Go Level 2> Function> System> RCON Backup,
Make P Print
Do RCON clear
Level 2 Function> System > RCON Restore
Not all values are restored so:
Input RCon values. from P PRINT

If the problem persists:
1 reseat flex cable from Reader Controller to Scanner unit in the READER
2 One of these has a problem ( Reader Controller, Scanner Unit, or Flex Cable) ALL in The READER

E302-0101 refers to the same parts in DF (backside scanner)


http://www.copytechnet.com/forums/canon/69065-ir-adv-6065-code-error-e302-0101-a.html

[buboy2222]

Re: IRADV 8095 E 302-001

E302-0001 refers to Front side scanning
I think there is a break in your flex cable which shows up when scanner reaches the slide read position
Go Level 2> Function> System> RCON Backup,
Make P Print
Do RCON clear
Level 2 Function> System > RCON Restore
Not all values are restored so:
Input RCon values. from P PRINT

If the problem persists:
1 reseat flex cable from Reader Controller to Scanner unit in the READER
2 One of these has a problem ( Reader Controller, Scanner Unit, or Flex Cable) ALL in The READER

E302-0101 refers to the same parts in DF (backside scanner)


http://www.copytechnet.com/forums/canon/69065-ir-adv-6065-code-error-e302-0101-a.html

Sir i got canon ir advance 6075 with same problem error 302-0001. i remove the whole assembly in DADF reader and clean but nothing happen. I reset the rcon but my problem is how to input manually the rcon values and how to go into level 2 service mode?
Hopefully you can give a little advice.
Thank you.

[dan7777]

Re: IRADV 8095 E 302-001

Sir i got canon ir advance 6075 with same problem error 302-0001. i remove the whole assembly in DADF reader and clean but nothing happen. I reset the rcon but my problem is how to input manually the rcon values and how to go into level 2 service mode?
Hopefully you can give a little advice.
Thank you.

When you lift the adf the cover in the back side behind the large glass you have to take off to take the connectors out has the factory settings under it. After you clean the glass in the scanner do a

Level 1> Copier>Function>CCD

DF-WLVL1=1 Ok
DF-WLVL1=2 Ok
DF-WLVL1=LNR=1 Ok

DF-WLVL1=3 Ok
DF-WLVL1=4 Ok
BW-TGT




I checked, the e302-0001 is for the scanner under the glass. There are other codes for codes of the scanner for back side in the adf. I don't clean that glass every call so it can get very dirty in a dirty environment. 30 years ago it was minimum call to clean scanner mirrors. For those settings clean white paper goes through the doc feeder and one setting on the glass. I put a piece of letter paper on the glass and one in the doc feeder and then run the settings.

[kiloa22]

Re: IRADV 8095 E 302-001

When you lift the adf the cover in the back side behind the large glass you have to take off to take the connectors out has the factory settings under it. After you clean the glass in the scanner do a

Level 1> Copier>Function>CCD

DF-WLVL1=1 Ok
DF-WLVL1=2 Ok
DF-WLVL1=LNR=1 Ok

DF-WLVL1=3 Ok
DF-WLVL1=4 Ok
BW-TGT




I checked, the e302-0001 is for the scanner under the glass. There are other codes for codes of the scanner for back side in the adf. I don't clean that glass every call so it can get very dirty in a dirty environment. 30 years ago it was minimum call to clean scanner mirrors. For those settings clean white paper goes through the doc feeder and one setting on the glass. I put a piece of letter paper on the glass and one in the doc feeder and then run the settings.

This is what I got:

DF-WLVL1=1 Ok
DF-WLVL1=2 NG!
DF-WLVL1=LNR=1 Ok

DF-WLVL1=3 Ok
DF-WLVL1=4 NG!
BW-TGT = OK

What should I do?

Thanks!

[dan7777]

Re: IRADV 8095 E 302-001

This is what I got:

DF-WLVL1=1 Ok
DF-WLVL1=2 NG!
DF-WLVL1=LNR=1 Ok

DF-WLVL1=3 Ok
DF-WLVL1=4 NG!
BW-TGT = OK

What should I do?

Thanks!

clean the mirror in the scanner. Replace scanner and/or cable. Has to be that or board.

[jio9000]

Re: IRADV 8095 E 302-001

Hi all,
I have a problem with the photocopier iradv 8095 with error E302-0001. are the connections to reader controller ok.Copy of glass is ok.
Copying from the document feeder causes an error .

any ideas

check the lamp strips on the reader unit, ensure that both are getting power or lighting up / properly conected .