[Game] Guilty -or- Not Guilty

[Copier_Guy]

A. Guilty

Q. Do you ever get fucked off with new members PMing you for free service manuals all the time???

A. Guilty (I always tell them to post on the board and almost never hear from them again. They don't post either from what I've seen. Shy Maybe!)


Q. Have you ever been instumental in selling or upgrading a machine where the company has a compensation program, only to find out much later the machine was sold and your manager collected the payout?

[Cipher]

A. Guilty (It does not pay to give a tech a hard time is all I'll say LOL).

Q. Have you ever done a 'botch' job to keep a customer up and running just to realize the botch you actually did works better than the proper part?

A. Guilty

Q. Do you ever get fucked off with new members PMing you for free service manuals all the time???

[Cipher]

Q. Have you ever left part of a customer's machine down, so they couldn't sort or use the doc feeder for a few days, while you "ordered a part" that was already in the back of your car?

A. Guilty (It does not pay to give a tech a hard time is all I'll say LOL).

Q. Have you ever done a 'botch' job to keep a customer up and running just to realize the botch you actually did works better than the proper part?

[10871087]

Q. Have you ever been caught having a 'perve' at a nice looking lady in an office - whilst pretending to fix a machine?

A. Not-Guilty (never been caught is more accurate)


Q. Have you ever left part of a customer's machine down, so they couldn't sort or use the doc feeder for a few days, while you "ordered a part" that was already in the back of your car?

[wagon]

Q. Have you ever walked into an account with the best intentions, but after being treated rudely, performed a Hit-N-Run and felt good when the call came right back?

A. Guilty.

Q. Have you ever been caught having a 'perve' at a nice looking lady in an office - whilst pretending to fix a machine?

[Copier_Guy]

A. Almost guilty

Q. Have you ever spoken to a customer in a manner rude enough for them to complain about you?

A. Not Guilty


Q. Have you ever walked into an account with the best intentions, but after being treated rudely, performed a Hit-N-Run and felt good when the call came right back?

[wagon]

Q. Have you ever been spoken to so rudely by a customer that you just grabbed your tool case and walked out.

A. Almost guilty

Q. Have you ever spoken to a customer in a manner rude enough for them to complain about you?

[Cipher]

A: Guilty

Q: Have you ever run up a large bar tab on the company card?

Not Guilty

Q. Have you ever been spoken to so rudely by a customer that you just grabbed your tool case and walked out.

[knightfall]

Not Guilty (I only drink in moderation and then only on special occasions).

Q. Have you ever run up a massive room service bill on the company credit card?

A: Guilty

Q: Have you ever run up a large bar tab on the company card?

[Cipher]

Q. Have you ever shown up to work with a hangover?

Not Guilty (I only drink in moderation and then only on special occasions).

Q. Have you ever run up a massive room service bill on the company credit card?

[wagon]

Q. Have you ever replaced a part that didn't need replacing, just to keep your boss or the customer off your back?

A. Guilty (then I stash the old part for later)

Q. Have you ever shown up to work with a hangover?

[Cipher]

Q. Have you ever reset a counter (say, a waste box or web) when that area had not been serviced?

A. Guilty (I reset the odd PM counter on things I know have no problem going past yield, but not on parts that would cause a major problem on failure).

Q. Have you ever replaced a part that didn't need replacing, just to keep your boss or the customer off your back?

[wagon]

Q. Have you ever stripped a machine down only to be left with a bunch of screws after you have finished rebuilding it?

A. Guilty. (but not anymore, have grown out of it)

Q. Have you ever reset a counter (say, a waste box or web) when that area had not been serviced?

[Cipher]

Q. Have you ever blamed the fact a customer has been sold the 'wrong' machine on the salesman when things go wrong - to get you out of the s@#t?

A. Guilty (but it's so true sometimes).

Q. Have you ever stripped a machine down only to be left with a bunch of screws after you have finished rebuilding it?

[wagon]

Q. Have you ever turned up to work feeling ill knowing that you should of really called in sick and then to cap things off you are handed the service call from hell?

A. Guilty.

Q. Have you ever blamed the fact a customer has been sold the 'wrong' machine on the salesman when things go wrong - to get you out of the s@#t?