CANON MX926 Error B200

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • NeoMatrix
    Senior Tech.

    2,500+ Posts
    • Nov 2010
    • 3513
    #1

    CANON MX926 Error B200

    I have an MX926 land on w/s bench with a B200 code on the display.
    "Turn off machine and call the service repair agent etc etc"...

    I don't have an e-manual for this machine.

    I believe it might be the print head jambing... A quick play around confirmed that I can't get full travel out of the print head.
    I'm not sure the machine is even worth fixing. I'm inclined to write it off for used parts.

    Anyone want any used parts from the above machine? Send me a PM.


    tnx
    Inauguration to the "AI cancel-culture" fraternity 1997...
    •••••• •••[§]• |N | € | o | M | Δ | t | π | ¡ | x | •[§]••• ••••••
    Tags: None
    • teckat
      Field Supervisor

      Site Contributor
      10,000+ Posts
      • Jan 2010
      • 16083
      #2
      Re: CANON MX926 Error B200

      1. Open the cover of the printer.
      2. Remove all ink tanks from the printer.
      3. Lift up the gray locking lever on the side of the ink tank holder.
      4. Gently remove the print head from the carriage unit.
      5. Place the print head back in and lock the lever down.
      6. Place all of the ink tanks back in the printer.
      7. Close the cover and turn the printer off.
      8. Unplug the power from the printer. Leave the power unplugged for about 5-10 minutes.
      9. Plug the power back in and turn the printer on.
      **Knowledge is time consuming, exhausting and costly for a trained Tech.**

        Comment

        • NeoMatrix
          Senior Tech.

          2,500+ Posts
          • Nov 2010
          • 3513
          #3
          Re: CANON MX926 Error B200

          Update...
          Could not resolve the issue. The scan motor metal casing gives off electrical current when touched.
          I've since placed the machine in the care of the surplus-to-requirements containment department, awaiting executive decision to close the case (AKA the lid of the rubbish bin) .
          Inauguration to the "AI cancel-culture" fraternity 1997...
          •••••• •••[§]• |N | € | o | M | Δ | t | π | ¡ | x | •[§]••• ••••••

            Comment

            • teckat
              Field Supervisor

              Site Contributor
              10,000+ Posts
              • Jan 2010
              • 16083
              #4
              Re: CANON MX926 Error B200

              Your posting of personal advertising as an active link is not allowed , unless you pay for this service .

              seems u have not learned ---------------- and anyone who pays for that service on that site is a JERK -

              **Knowledge is time consuming, exhausting and costly for a trained Tech.**

                Comment

                • Technotronic
                  Technician
                  • Feb 2006
                  • 23
                  #5
                  Re: CANON MX926 Error B200

                  Saw a video that says to clean the printer head in water. Has anyone here done this w success?

                    Comment

                    • campy
                      Trusted Tech

                      250+ Posts
                      • May 2012
                      • 315
                      #6
                      Re: CANON MX926 Error B200

                      It's not worth fixing, unless your labor rate is $25 per hour. Googled it and they sell for $159.

                        Comment

                        • Technotronic
                          Technician
                          • Feb 2006
                          • 23
                          #7
                          Re: CANON MX926 Error B200

                          In this case its a MG8120, I'm seeing them for $180 - $200 or so. Not sure if the error code is the same as the model in this
                          discussion, I am guessing its the same. Client says its about 7 yrs old, looks like its been kept in really decent shape, hate to think
                          its beyond repair, but I guess if its the print head, I have seen that part go for some outrageous costs when I use to service Brother stuff.


                          Originally posted by campy
                          It's not worth fixing, unless your labor rate is $25 per hour. Googled it and they sell for $159.

                            Comment

                            • campy
                              Trusted Tech

                              250+ Posts
                              • May 2012
                              • 315
                              #8
                              Re: CANON MX926 Error B200

                              If you could talk to Canon tech support, they would tell you it's either the print head or the board. That's what they always told us. We stopped servicing the ink jet printers, there's no money in it. Between Canon and Brother I get at least one call a day for ink jet and I tell them get a new one. Some Brother printers cost $59 and I tell them it cost you $59 just to talk to me.

                                Comment

                                Previous template Next
                                Working...