Inner Finisher F-1

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • RHodg57
    Trusted Tech

    100+ Posts
    • Dec 2013
    • 191
    #1

    Inner Finisher F-1

    Having problems with this finisher on an IRADVC2230. The tray does not go to the home position. Tried a different

    tray assembly but it didn't change anything. It was received with the stapler and gripper unit off track. I got those straightened

    out. It will output paper and even staple okay. but the tray goes to the bottom and never comes back up. I made sure the

    the upper limit switch was functioning properly. Any ideas?
    Tags: None
    • dan7777
      Senior Tech

      500+ Posts
      • Dec 2012
      • 680
      #2
      Re: Inner Finisher F-1

      Originally posted by RHodg57
      Having problems with this finisher on an IRADVC2230. The tray does not go to the home position. Tried a different

      tray assembly but it didn't change anything. It was received with the stapler and gripper unit off track. I got those straightened

      out. It will output paper and even staple okay. but the tray goes to the bottom and never comes back up. I made sure the

      the upper limit switch was functioning properly. Any ideas?
      It may be the sensor on the tray. I have had two issues with them. Make sure it is locked in and not one side up. Does it give an error code? The wire harness also can go bad. Usually the top tray but have had to replace bottom tray on a 2870 (this tray would not move correctly). Same kind of symptom. Noticed there was a spring broken and new tray had a screw locking the gear where the spring was. Right at the worm gear drive. If you have another tray to try I would suggest that.

        Comment

        • RHodg57
          Trusted Tech

          100+ Posts
          • Dec 2013
          • 191
          #3
          Re: Inner Finisher F-1

          Originally posted by dan7777
          It may be the sensor on the tray. I have had two issues with them. Make sure it is locked in and not one side up. Does it give an error code? The wire harness also can go bad. Usually the top tray but have had to replace bottom tray on a 2870 (this tray would not move correctly). Same kind of symptom. Noticed there was a spring broken and new tray had a screw locking the gear where the spring was. Right at the worm gear drive. If you have another tray to try I would suggest that.

          I had tried that with a known working tray and no luck. It's weird that it will go down but not up. Have had inner finishers for

          years and never seen one do this.

            Comment

            • dan7777
              Senior Tech

              500+ Posts
              • Dec 2012
              • 680
              #4
              Re: Inner Finisher F-1

              Originally posted by RHodg57
              I had tried that with a known working tray and no luck. It's weird that it will go down but not up. Have had inner finishers for

              years and never seen one do this.
              That is strange. My issues have always been in the tray somewhere (sensor, motor, gear, wire harness). I have not had an issue with the board in them yet.

                Comment

                • RHodg57
                  Trusted Tech

                  100+ Posts
                  • Dec 2013
                  • 191
                  #5
                  Re: Inner Finisher F-1

                  Originally posted by dan7777
                  That is strange. My issues have always been in the tray somewhere (sensor, motor, gear, wire harness). I have not had an issue with the board in them yet.
                  I started to reseat the connectors on the control board and discovered a damaged connector with a broken wire. The connector

                  for the tray. All makes sense now except how it got damaged. Anyways, good to go now. Thanks for your suggestions!!

                    Comment

                    Previous template Next
                    Working...