Canon Imagerunner 2020 - Nothing showing up on Control Panel

[screwdriver08]

Re: Canon Imagerunner 2020 - Nothing showing up on Control Panel

I don't think FM-1920 is the correct partno. I Found FM3-1920 but thats for a 2016 ?

Canon IMAGE PROCESSOR PCB ASS'Y, (IR2016 TW 120V) (FM3-1920-000000) - Mediaform Computer Supplies

Not sure if that is what you need, i'd recheck if i where you..

Thank You, I will email that company and check if they have it in stock..thank you so much

[JPiek]

Re: Canon Imagerunner 2020 - Nothing showing up on Control Panel

I don't think FM-1920 is the correct partno. I Found FM3-1920 but thats for a 2016 ?

Canon IMAGE PROCESSOR PCB ASS'Y, (IR2016 TW 120V) (FM3-1920-000000) - Mediaform Computer Supplies

Not sure if that is what you need, i'd recheck if i where you..

[screwdriver08]

Re: Canon Imagerunner 2020 - Nothing showing up on Control Panel

Item inc (printer parts and supplies and rentals item inc) may have it, just google the partno to compare prices...

Thank You, they were the first ones I checked with and they did not have it in stock.
Thanks

[JPiek]

Re: Canon Imagerunner 2020 - Nothing showing up on Control Panel

Item inc (printer parts and supplies and rentals item inc) may have it, just google the partno to compare prices...

[screwdriver08]

Re: Canon Imagerunner 2020 - Nothing showing up on Control Panel

Thank You,

Now does anyone know where I can buy such a part for my Machine?
I checked the Board and it does have FM-1920 on it, but am not so sure where I can buy such a part.
I really need this machine to work, have had it down like this, not working for almost four months now.

[clivealive]

Re: Canon Imagerunner 2020 - Nothing showing up on Control Panel

I've had a couple of these. In both cases it was the Main Controller 1. Replaced this board, and hey presto, back to life. But you can only fit a new one, and it must be the specific model, as they are locked to speed and set the serial number when powered on.

Fig.930 FM4-3139-010 1 MAIN CONTROLLER PCB ASS'Y, 1 C2020 SERIES

Fig.930 FM4-3140-010 1 MAIN CONTROLLER PCB ASS'Y, 1 C2025 SERIES

Fig.930 FM4-3141-010 1 MAIN CONTROLLER PCB ASS'Y, 1 C2030 SERIES

Also had same fault on IrAdv4025, and IrAdvC5051 which was also Main Controller 1 on both counts .... expensive hobby!

[screwdriver08]

Re: Canon Imagerunner 2020 - Nothing showing up on Control Panel

Does anyone here have the firmware for Canon Imagerunner 2020 that is willing to share with me?

[JPiek]

Re: Canon Imagerunner 2020 - Nothing showing up on Control Panel

Check PM...

[screwdriver08]

Re: Canon Imagerunner 2020 - Nothing showing up on Control Panel

I think you should do a Boot system error diagnostics, but you would need the manual to go through these steps and find out what is defective...
(Start at page 6 - 86, Controller Self Diagnosis > Basic Flowchart)

Thank You JPiek, do you know where I could get such manual at? Or the name of the manual so I can look for it online.
Thank You so much

[JPiek]

Re: Canon Imagerunner 2020 - Nothing showing up on Control Panel

I think you should do a Boot system error diagnostics, but you would need the manual to go through these steps and find out what is defective...
(Start at page 6 - 86, Controller Self Diagnosis > Basic Flowchart)

[screwdriver08]

Re: Canon Imagerunner 2020 - Nothing showing up on Control Panel

No, just press 2and 8 and hold them while powering on.. Keep them pressed until booting in finished (if it will boot)...

Thanks JPiek, I just tried that but nothing happened.
It is just like before, where when I turn on the power button you can hear the machine run for like two or three seconds and then it stops.
Still not displaying anything.

[JPiek]

Re: Canon Imagerunner 2020 - Nothing showing up on Control Panel

JPiek, Thank You, but I tried pressing down the numbers 2 AND 8 on the Control Panel and nothing happened. It just turned on like before, it would just turn on and makes the sound like it is about to initialize and then stops. But only the light on POWER on the Control Panel is on.

Do I have to connect it to a Computer to do what you instructed?

No, just press 2and 8 and hold them while powering on.. Keep them pressed until booting in finished (if it will boot)...

[screwdriver08]

Re: Canon Imagerunner 2020 - Nothing showing up on Control Panel

reload system software

Thanks for the Reply Copyman, can you please tell me how to reload the system software?

Thanks

[screwdriver08]

Re: Canon Imagerunner 2020 - Nothing showing up on Control Panel

Can you boot into download mode (press 2+8 and power on) ?

JPiek, Thank You, but I tried pressing down the numbers 2 AND 8 on the Control Panel and nothing happened. It just turned on like before, it would just turn on and makes the sound like it is about to initialize and then stops. But only the light on POWER on the Control Panel is on.

Do I have to connect it to a Computer to do what you instructed?

[JPiek]

Re: Canon Imagerunner 2020 - Nothing showing up on Control Panel

Can you boot into download mode (press 2+8 and power on) ?