IRC2880i Error Code 000025-001

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • belhocines
    #1

    IRC2880i Error Code 000025-001

    Hello everybody

    I've got problem with my IRC2880i printer. It is that the screen reads "Error 000025-001" and the machine requests reboot. Booting is ok, but when trying to print the machine begins to pull the paper and stops and the problem occurs.
    And .

    Any help please!!!
    Tags: activated, amou, code, control panel, dirty, dos, dosnt, error, executing, help please, image runner, irc2880i, life, ops, wrong
    • BLITZKREAGG
      #2
      irc 2880

      Error :
      E025 0000 code

      Workaround :
      Check for loose or pinched wires on the (Kit) connector board at J551 and J552.

      Product : imageRUNNER C3380 / C2880 Title : E025 Error code Error :
      E025 error code is indicated when a copy in color mode is made.

      The toner for each color is fed from the toner retainer, via the hopper assembly, to the drum unit. There are two kinds of toner feeding, one is hopper feeding from the toner retainer to the hopper assembly and another is drum feeding from the hopper assembly to the drum unit.
      If all is normal, the toner supply motor (M8-M11) rotates clockwise (CW). If something goes wrong and the motor rotates counterclockwise (CCW), however, the toner supply feed-screw will rotate to cause a change in the output of PS3 through PS6 (with the machine assuming malfunction of the toner supply motor).

      To execute correct toner feeding, this machine has a toner feed level sensor (PS3-PS6). This sensor detects the sensor flag mounted on the shaft of the feed screw. This sensor flag executes reciprocating movement by the drive of the toner feed motor. It is the structure that the toner feed screw rotates and the specific amount of toner is fed to the drum unit when the sensor flag moves back and forth once.

      At the time of the toner feeding, the DC controller monitors this sensor while driving the toner feed motor. The toner feed motor is stopped when feeding is completed. By executing this, the toner feeding is correctly implemented.




      Workaround :



      [1] Stirring plate
      [2] Agitating plate
      [3] Scraping spring
      [4] Sensor flag
      [5] Toner feed screw
      [6] Toner feed motor drive signal
      [7] Toner feed motor error detection signal
      [8] toner container
      [9] Hopper assembly
      [10] drum unit
      M8 through M11: Toner feed motor (FM2-5597-000)
      PS3 through PS5: Toner feed level sensor (WG8-5772-000)
      PS6: Toner feed level sensor for black (FK2-0149-000)

      If the Toner feed motors (M8 through M11) can be activated in service mode under PART-CHK, suspect a fault at Toner feed level sensor (PS3 through PS6).

      Title : Error Code E025 on Image Runner C3380/C2880 Error :
      Error code E025 is displayed

      Workaround :
      Error Code E025-xxxx
      Symptom
      An E025-xxxx error code is displayed on the control panel.
      Cause
      Defective Drum Unit
      Blocked Toner Pipe (High Humidity / High Temperature Environment)
      Loose/ Faulty Wiring
      Faulty/ Dirty Toner Feed Level Sensor
      Faulty Toner Supply Motor
      Defective Connecting PCB Unit
      Defective DC Controller PCB Assembly
      Action
      Check for a broken or jammed toner supply auger on the Drum Assembly.
      Check the toner holes on the Drum and Hopper Assembly. Use a vacuum to clear any blockage found.


      Also check that the sensor lever is not jammed
      Check for loose or pinched wires on the Connecting PCB Unit at J551 and J552.
      If the Toner feed motors (M8 through M11) can be activated in service mode under PART-CHK, suspect a fault at Toner feed level sensor. First clean the sensor, if found to be faulty replace it with a new one:
      PS3 through PS5: Toner feed level sensor (WG8-5772-000)
      PS6: Toner feed level sensor for black (FK2-0149-000)
      Replace the Toner Supply Motor and check the connectors at the DC Controller PCB. Use the following chart as a reference:
      Ref. Description Part Number DC Controller PCB
      Connector Error Code
      M8 Toner supply motor (Y) FM2-5597 J2012 E025-0000
      E025-0100
      M9 Toner supply motor (M) FM2-5597 J2010 E025-0001
      E025-0101
      M10 Toner supply motor (C) FM2-5597 J2008 E025-0002
      E025-0102
      M11 Toner supply motor (K) FM2-5597 J2005 E025-0003
      E025-0103
      Replace the Connecting PCB Unit (FM2-8266-000)
      Replace the DC Controller PCB Assembly (FM2-8263-000)

      Title : Error Code E025 on Image Runner C3380/C2880 Error :
      Error code E025 is displayed

      Workaround :
      Error Code E025-xxxx
      Symptom
      An E025-xxxx error code is displayed on the control panel.
      Cause
      Defective Drum Unit
      Blocked Toner Pipe (High Humidity / High Temperature Environment)
      Loose/ Faulty Wiring
      Faulty/ Dirty Toner Feed Level Sensor
      Faulty Toner Supply Motor
      Defective Connecting PCB Unit
      Defective DC Controller PCB Assembly
      Action
      Check for a broken or jammed toner supply auger on the Drum Assembly.
      Check the toner holes on the Drum and Hopper Assembly. Use a vacuum to clear any blockage found.


      Also check that the sensor lever is not jammed
      Check for loose or pinched wires on the Connecting PCB Unit at J551 and J552.
      If the Toner feed motors (M8 through M11) can be activated in service mode under PART-CHK, suspect a fault at Toner feed level sensor. First clean the sensor, if found to be faulty replace it with a new one:
      PS3 through PS5: Toner feed level sensor (WG8-5772-000)
      PS6: Toner feed level sensor for black (FK2-0149-000)
      Replace the Toner Supply Motor and check the connectors at the DC Controller PCB. Use the following chart as a reference:
      Ref. Description Part Number DC Controller PCB
      Connector Error Code
      M8 Toner supply motor (Y) FM2-5597 J2012 E025-0000
      E025-0100
      M9 Toner supply motor (M) FM2-5597 J2010 E025-0001
      E025-0101
      M10 Toner supply motor (C) FM2-5597 J2008 E025-0002
      E025-0102
      M11 Toner supply motor (K) FM2-5597 J2005 E025-0003
      E025-0103
      Replace the Connecting PCB Unit (FM2-8266-000)
      Replace the DC Controller PCB Assembly (FM2-8263-000)

      Title : Error Code E025 on Image Runner C3380/C2880 Error :
      Error code E025 is displayed

      Workaround :
      Error Code E025-xxxx
      Symptom
      An E025-xxxx error code is displayed on the control panel.
      Cause
      Defective Drum Unit
      Blocked Toner Pipe (High Humidity / High Temperature Environment)
      Loose/ Faulty Wiring
      Faulty/ Dirty Toner Feed Level Sensor
      Faulty Toner Supply Motor
      Defective Connecting PCB Unit
      Defective DC Controller PCB Assembly
      Action
      Check for a broken or jammed toner supply auger on the Drum Assembly.
      Check the toner holes on the Drum and Hopper Assembly. Use a vacuum to clear any blockage found.


      Also check that the sensor lever is not jammed
      Check for loose or pinched wires on the Connecting PCB Unit at J551 and J552.
      If the Toner feed motors (M8 through M11) can be activated in service mode under PART-CHK, suspect a fault at Toner feed level sensor. First clean the sensor, if found to be faulty replace it with a new one:
      PS3 through PS5: Toner feed level sensor (WG8-5772-000)
      PS6: Toner feed level sensor for black (FK2-0149-000)
      Replace the Toner Supply Motor and check the connectors at the DC Controller PCB. Use the following chart as a reference:
      Ref. Description Part Number DC Controller PCB
      Connector Error Code
      M8 Toner supply motor (Y) FM2-5597 J2012 E025-0000
      E025-0100
      M9 Toner supply motor (M) FM2-5597 J2010 E025-0001
      E025-0101
      M10 Toner supply motor (C) FM2-5597 J2008 E025-0002
      E025-0102
      M11 Toner supply motor (K) FM2-5597 J2005 E025-0003
      E025-0103
      Replace the Connecting PCB Unit (FM2-8266-000)
      Replace the DC Controller PCB Assembly (FM2-8263-000)

      Error :
      Error code E025 is displayed

      Workaround :
      Error Code E025-xxxx
      Symptom
      An E025-xxxx error code is displayed on the control panel.
      Cause
      Defective Drum Unit
      Blocked Toner Pipe (High Humidity / High Temperature Environment)
      Loose/ Faulty Wiring
      Faulty/ Dirty Toner Feed Level Sensor
      Faulty Toner Supply Motor
      Defective Connecting PCB Unit
      Defective DC Controller PCB Assembly
      Action
      Check for a broken or jammed toner supply auger on the Drum Assembly.
      Check the toner holes on the Drum and Hopper Assembly. Use a vacuum to clear any blockage found.


      Also check that the sensor lever is not jammed
      Check for loose or pinched wires on the Connecting PCB Unit at J551 and J552.
      If the Toner feed motors (M8 through M11) can be activated in service mode under PART-CHK, suspect a fault at Toner feed level sensor. First clean the sensor, if found to be faulty replace it with a new one:
      PS3 through PS5: Toner feed level sensor (WG8-5772-000)
      PS6: Toner feed level sensor for black (FK2-0149-000)
      Replace the Toner Supply Motor and check the connectors at the DC Controller PCB. Use the following chart as a reference:
      Ref. Description Part Number DC Controller PCB
      Connector Error Code
      M8 Toner supply motor (Y) FM2-5597 J2012 E025-0000
      E025-0100
      M9 Toner supply motor (M) FM2-5597 J2010 E025-0001
      E025-0101
      M10 Toner supply motor (C) FM2-5597 J2008 E025-0002
      E025-0102
      M11 Toner supply motor (K) FM2-5597 J2005 E025-0003
      E025-0103
      Replace the Connecting PCB Unit (FM2-8266-000)
      Replace the DC Controller PCB Assembly (FM2-8263-000)

        Comment

        • Irish
          Trusted Tech

          100+ Posts
          • Nov 2007
          • 110
          #3
          Life is much more simple than this.. Toner has droped into the flag arm sensors. Quick fix.. Remove gray plastic cover over sensors (under toner Hoppers) and use air duster to blow through holes of pcb behind. this is hit and miss but usually works short term. For proper fix also remove pcb .clean photo sensors and cover top and non flag side of sensor with sellotape or simular. not possible with black (right hand side)but this dosnt appear to suffer from falling toner ... Good Luck

            Comment

            Previous template Next
            Working...