[Error Code] error code E020-02A9 on C5550i II

[marc van de ven]

hi all,

i am struggeling with error code E020-02A9.
it its only possible to print or copy in bk and white.
as soon as i print or copy in color i get error code E020-02A9 The ATR Sensor (M) detected that the output value exceeded the upper limit during printing.
what i did so far:
replaced all developerassy and developer HV pcb. i did the init-all. dens vallue all 0%
first color test, immideately error E030-02A9
backuped dc and printed p-print
did a dc-con clear. afther reboot, init-all , still no luck.

i now ordered dc controller pcb.
any other suggestions or others with experiences on this error?

[mosey1100]

Re: error code E020-02A9 on C5550i II

hi all,

i am struggeling with error code E020-02A9.
it its only possible to print or copy in bk and white.
as soon as i print or copy in color i get error code E020-02A9 The ATR Sensor (M) detected that the output value exceeded the upper limit during printing.
what i did so far:
replaced all developerassy and developer HV pcb. i did the init-all. dens vallue all 0%
first color test, immideately error E030-02A9
backuped dc and printed p-print
did a dc-con clear. afther reboot, init-all , still no luck.

i now ordered dc controller pcb.
any other suggestions or others with experiences on this error?

Did you check the following

E020-02A9 - ATR output error

Detection Description
The ATR Sensor (M) detected that the output value exceeded the upper limit during printing.

Remedy
[Related parts] R1.00
- Harnesses connecting the Process Unit Relay PCB (UN20/J609), the Relay Connector (J5094/5P) and the ATR Sensor (M) (TS6/J6116)
- Developing Assembly (M)

[Remedy] Check/replace the related harness/cable, connector and parts.

[marc van de ven]

Re: error code E020-02A9 on C5550i II

Did you check the following

E020-02A9 - ATR output error

Detection Description
The ATR Sensor (M) detected that the output value exceeded the upper limit during printing.

Remedy
[Related parts] R1.00
- Harnesses connecting the Process Unit Relay PCB (UN20/J609), the Relay Connector (J5094/5P) and the ATR Sensor (M) (TS6/J6116)
- Developing Assembly (M)

[Remedy] Check/replace the related harness/cable, connector and parts.

yes i checked all that.

[mga]

Re: error code E020-02A9 on C5550i II

hi all,

i am struggeling with error code E020-02A9.
it its only possible to print or copy in bk and white.
as soon as i print or copy in color i get error code E020-02A9 The ATR Sensor (M) detected that the output value exceeded the upper limit during printing.
what i did so far:
replaced all developerassy and developer HV pcb. i did the init-all. dens vallue all 0%
first color test, immideately error E030-02A9
backuped dc and printed p-print
did a dc-con clear. afther reboot, init-all , still no luck.

i now ordered dc controller pcb.
any other suggestions or others with experiences on this error?

Why does everyone always think these problems are pwb related have you done all the basics checked pm life clean all id sensors etc I hardly ever replace boards

Edited {nearly everyone not included the experience guys you know who I mean}

[marc van de ven]

Re: error code E020-02A9 on C5550i II

Why does everyone always think these problems are pwb related have you done all the basics checked pm life clean all id sensors etc I hardly ever replace boards

Edited {nearly everyone not included the experience guys you know who I mean}

PROBLEM SOLVED!!!!!!!!!!!
i replaced 'charge HV board'

[mga]

Re: error code E020-02A9 on C5550i II

PROBLEM SOLVED!!!!!!!!!!!
i replaced 'charge HV board'

Well done