iR4045i with E261_000 Try to reconnect J113/J202 but don't work
Question
1. Is There anything I should do before replacePower PCB or DC PCB ?
2. Can I Try to test Swap with iR 4051 to check which PCB is bad
I saw this great advice of teckat so I will follow but I need to ask before I have to replace Power PCB or DC PCB it will cost me alot. , Thank you.
----------------------------------------------
COPIER>FUNCTION>CLEAR>ERR
Use this mode to clear an error code: E000, E001, E002, E003, E004, E032, E717.
Using the Mode= will not function on E261
1) Select <ERR> to highlight, and press the OK key.
2) Turn off and then on the main power switch.
U NEED TO INVESTIGATE
the input/output ports of the DC controller PCBs.
COPIER>I/O>DC-CON<DC-CON (5/7)>
P020 xxxxxxxxxxxxxxxx=runs from left to right 15>0
ADDRESS=P020
BIT-
0- zero-cross signal -
1- heater trigger 1 signal 0: ON
2- heater trigger 2 signal 0: ON
3- heater error OFF signal 0: error
4- not used
5- not used
6- M9 registration motor phase A pulse signal -
7- M9 registration motor phase B pulse signal -
E261 0000
The intervals of zero-cross signals deviate from the tolerance range while
the fixing heater is supplied with power.
Main cause The wiring is faulty (short circuit, open circuit). The main power supply
PCB is faulty. The DC controller PCB is faulty.
Making Corrections
1. Connectors
Are the connectors J205 on the main power supply PCB and the connector
J308B on the DC controller PCB securely connected?
(zero-cross signal: J205-7 <-> J308B-1)
NO: Connect the connectors securely.
2. Main power supply PCB, Main controller PCB
Try replacing the main power supply PCB. Is the problem corrected?
YES: End.
NO: Replace the DC controller PCB.
Question
1. Is There anything I should do before replacePower PCB or DC PCB ?
2. Can I Try to test Swap with iR 4051 to check which PCB is bad
I saw this great advice of teckat so I will follow but I need to ask before I have to replace Power PCB or DC PCB it will cost me alot. , Thank you.
----------------------------------------------
COPIER>FUNCTION>CLEAR>ERR
Use this mode to clear an error code: E000, E001, E002, E003, E004, E032, E717.
Using the Mode= will not function on E261
1) Select <ERR> to highlight, and press the OK key.
2) Turn off and then on the main power switch.
U NEED TO INVESTIGATE
the input/output ports of the DC controller PCBs.
COPIER>I/O>DC-CON<DC-CON (5/7)>
P020 xxxxxxxxxxxxxxxx=runs from left to right 15>0
ADDRESS=P020
BIT-
0- zero-cross signal -
1- heater trigger 1 signal 0: ON
2- heater trigger 2 signal 0: ON
3- heater error OFF signal 0: error
4- not used
5- not used
6- M9 registration motor phase A pulse signal -
7- M9 registration motor phase B pulse signal -
E261 0000
The intervals of zero-cross signals deviate from the tolerance range while
the fixing heater is supplied with power.
Main cause The wiring is faulty (short circuit, open circuit). The main power supply
PCB is faulty. The DC controller PCB is faulty.
Making Corrections
1. Connectors
Are the connectors J205 on the main power supply PCB and the connector
J308B on the DC controller PCB securely connected?
(zero-cross signal: J205-7 <-> J308B-1)
NO: Connect the connectors securely.
2. Main power supply PCB, Main controller PCB
Try replacing the main power supply PCB. Is the problem corrected?
YES: End.
NO: Replace the DC controller PCB.
Comment